Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Motors

Posts

Motors

#1

Motors

Leslie S

>Does anyone have a suggestion for a source for a motor to use with a Beal system. I turn on a Jet Mini and have 8 inch buffing wheels. makes for a tight fit when trying to polish. I have seen them in cataloges for a few hundred dollars, I figure there has to be a better price somewhere. Any ideas?

Re: Motors

#2

Re: Motors

OB O'Brien

>Used washing machine motor.

Re: Motors

#3

Re: Motors

Wally Dickerman in Arizona

>Look up Electric motors in the yellow pages. Most motor shops will have used motors for not much money. A 1/4 or 1/3 HP motor will do just fine for the Beall system. Make sure that it's turning in the right direction before you leave the shop.

Wally

Re: Motors

#4

Re: Motors

Leslie S

>Next question. How does one make a motor for a Bealle out of a Wahing machine motor?

Re: Motors

#5

Re: Motors

Russ Babbitt

>When I upgraded the motor on my bandsaw I used the old motor for the Beall system. Ebay would be a good source for new or used motors. Amazon, Harbor Freight and others already mentioned. Flea markets and garage sales.


img

Re: Motors

#6

Re: Motors

Allen Neighbors

>Leslie, I located a motor that turned 1725 RPM. Then I attached an arbor (one that adapts the motor shaft to accept a grinding wheel) and re-threaded 1" of the arbor shaft to 1/2" threads to accept a 2" longnut. I screwed the long nut onto the arbor - tight - which left a 1/2" female thread. That accepts the buffing wheels I made that have a 1/2" bolt in the center.

My buffing wheels are quick to get on and off, using only about 1/2" of threads.

I don't know how the Beale buffs mount, probably different than my homemade ones, but this should give you an idea or two.

Hope this helps.

Re: Motors

#7

Re: Motors

Bill Hale / Woodspinner

>Leslie

You can also check out Surplus Center on the web. They have cheap motors of every size and type.

www.surpluscenter.com/

Cut and paste this to your browser

Bill in Casa Grande, AZ.

Re: Motors

#8

Re: Motors

Wally Dickerman in Arizona

>You should be looking for a 1725 RPM motor for the Beall system, not a 3450.

Wally

Re: Motors

#9

Re: Motors

OB O'Brien

>Beall has an attachment for a 1/2 or 5/8 ths inch shaft. The shaft of the motor has a flat on one side. You screw 2 set screws down to hold the adapter on. The buffs can then readily be changed. Here's a link for the system that shows it all.

http://www.packardwoodworks.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=123901&Category_Code=

Watch the links wrap around. Good luck OB

Re: Motors

#10

Leo Van Der Loo

Re: Motors *LINK*

Leo Van Der Loo

>Hi Leslie

Leslie I used a used oil furnace fan motor, 1/3 hp and 1725 rpm, I made the parts to put the pieces together, but you can buy those readily.

I use a keyed drill chuck as I had one, but a hand tightening one would be even quicker.

Here's a picture and also a link to the parts if you like to buy those.

Have fun and take care

leo Van Der loo


img

http://www.leevalley.com/wood/page.aspx?c=2&p=41743&cat=1,43072,45939

Re: Motors

#11

Re: Motors

Dinyar Chavda

>Is there any reason why you're not using the lathe? There are adaptors to hold the wheels either using a taper, or a threaded sleeve. The advantage of the lathe, of course, is that, assuming you have one with variable speed, you can adjust the speed to whatever you want it to be.