Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Sharpening gauge alignment

Posts

Sharpening gauge alignment

#1

Sharpening gauge alignment

john lucas

>Rick brought up an interesting question that I think we all have had problems with. I'll pass on my solution and listen to all the other ways you all do the same thing. This should be useful to new turners.

When I'm setting up the wolverine jig I used to just adjust it until the nose rubbed but I found this to be somewhat inaccurate. Now what I do is touch the nose for close alignment, then I'll shift it around and touch the sides (with the wheel off). I find I can see if the adjustment is off more accurately.

Someone at a show (I think It was Mark St.Leger) showed us to mark the tip with a magic marker. Then rotate the wheel by hand and see where it grinds. This is a really accurate way to set the jig. It's also really good if your sharpening by hand. It shows exactly what's been ground and what hasn't.

I know the best way would be to just use the same grind on all your tools then you never have to change things but I have a lot of tools and like to play with grinds to see what works. I also have tools ground for a certain purpose. To make sure my Wolverine can be reset to exactly the same point each time I adjust it, I drilled a hole through both plates. Then whenever I need to realign the jig I simply put a 1/8" drill bit in the holes and lock it down.

The best way I'm sure is to build a 3 point jig to set oneway V bar. 2 points touch the wheel and one goes in the V jig. This would let you set the jig in exactly the same place each time even if the wheel wears down. I've just never taken the time to do that. This is covered extensively in Woodturning Techniques by Mike Darlow.That one chapter is worth the price of the whole book.

Re: Sharpening gauge alignment

#2

Yet Another approach - profile jigs for VariGrind *LINK*

Mike Brazeau

>In the January 2006 Newsletter of the Woodturners Guild of Ontario, Rudi Schafron detailed a series of jigs, including pdf files of the outlines for setting up the Vari Grind attachment on the Wolverine. The article is titled Repeatable Grinds for Woodturners and available at the link below. You do need a relatively current version of Adobe Reader to see everything. I haven't tried it but have heard that it works quite well. Rudi is a production bowl turner.

Mike


WGO January 2006 Neswletter

Re: Sharpening gauge alignment

#3

small hijack

Tony Reynolds somewhere near Newark, Ohio

>Also check out Marilyn Campbell's excellent article on design in the same newsletter.

Tony

Re: Sharpening gauge alignment

#4

Re: Sharpening gauge alignment

Russ Babbitt

>I use what I call story sticks. Once I have determined the grind I want for my tools I will make a stick set to the length needed. On each stick is the angle that should result and the setting for the varigrind jig. Works for me and takes in the fact that the wheel will eventually get smaller. Making the end at the wheel flat would be a bit more user friendly.


img

Re: Sharpening gauge alignment

#5

great article.

john lucas

>Mike I've seen that before. Excellent article.

Re: Sharpening gauge alignment

#6

Re: Sharpening gauge alignment

Mike Cunningham (Cape May NJ)

>Exactly what I do on the Tormek. I color the entire bevel with a blue (color of course doesn't matter, it's what I have) sharpie. With the machine off I touch the tip and adjust until close. Turn on the machine and rotate to one side and check, then make the necessary adjustments. I do this on my "regular" grinder as well and with all turning tools, color the bevel.

Re: Sharpening gauge alignment

#7

Re: Yet Another approach - profile jigs for VariGr

Jennifer@Indy.USA

>What a great Newsletter! Thanks for the link Mike. I read it top to bottom!

Bookmarked it too.

Jen

Re: Sharpening gauge alignment

#8

VERY GOOD

Frank of Mantua NJ

>Very good ..Print the whole thing out Its a good news letter