Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Turning While Sitting

Posts

Turning While Sitting

#1

Turning While Sitting

Steve in NC

>Found out today that I need surgery to repair Anticular cartilage in my knee. Surgery does not seem too bad but the doc says I have to be non weight bearing on that leg for two months. Poor timing since I have about 20 Christmas gifts waiting to be finished at the lathe.

Surgery is next week so I tried setting up a stool to try turning while sitting. It felt very awkard and a bit unsafe (reaction time to flying objects). I seem to remember a thread a while back about this subject and several folks encouraged the idea but I cannot remember the details.

I have only this weekend to make any required modifications to be able to turn sitting down. My biggest question is what to sit on. Will I be better off on a stool at my larger Delta or should I remount my Jet mini to a table height and use a nornal height chair.

Any suggestions would be greatly appreciated.

Steve

PS The good news is that after ten eight weeks, the doc thinks I will be able to resume activites without restriction.

Re: Turning While Sitting

#2

Re: Turning While Sitting

Richard Prince

>Hi Steve.. I have a bad back and have trouble standing at the lathe for any length of time... I have found that sitting in a regular chair to my mini lathe works well and when I need to work at the large lathe I use a dental stool.. It has 5 castors and adjusts to meet my needs..I do find that I have to stand sometimes to see.

Re: Turning While Sitting

#3

Re: Turning While Sitting

eaglesc

>I am only a mere pen turner but I have 3 lathes set uo in such a way I can work on any one from a standard bar stool from Hooters.

I have a bad back and a screwed up knee.

Been doing it this way for over 2 years.

I also cut the handles down on my chisels.

Re: Turning While Sitting

#4

Re: Turning While Sitting

OB O'Brien

>I also have bad knees and can't stand for long. I have lowered my mini lathe and use a low chair on rollers. The lathes centerline is lowered to about where the top of my knees are. By resting my arms on my legs, i'm comfortable and use my whole body to do the dance with the lathe like when your standing up. On the larger lathes I use a taller stool and do the same thing. Shortened tool handle also help. Good luck, all it takes is a little practice. OB

Re: Turning While Sitting

#5

Re: Turning While Sitting

Bruce

>I mounted my mini on an old end table and used an old office chair with wheels and the back removed. I was a little hunched over at times but it seemed to work well. The shavings can get in the way when rolling from lathe to grinder and back.

Good luck with the surgery.

~b

Re: Turning While Sitting

#6

Sounds good

Mike Cunningham (Cape May NJ)

>Great idea, the only thing I ever turned from a Hooters bar stool was my head!

Seriously though I have back problems and we'll keep these suggestions in mind.

Re: Turning While Sitting

#7

Re: Turning While Sitting

Bill Hale / Woodspinner

>Steve

I would have to say to stay with the mini in a low profile. Using the large lathe would allow you to do larger work and increase the risk of needing to get out of the way of something. Auto responce would tell you to take the step that you should not be taking. You take an off balance step and re damage the knee.

It sounds like a good year to make ornaments, on the mini, for christmas gifts.

Be safe and good turning.

Bill in Casa Grande, AZ.

Re: Turning While Sitting

#8

Re: Turning While Sitting

Ben Aragon

>I have tried turning on my Powermatic while sitting on a stool. The problem is, to be at the right height my knees hit the lathe bed. I don't have a bad back or knees but I do get tired of standing for hours. Has anyone found a solution?

Ben

Re: Turning While Sitting

#9

Re: Turning While Sitting - Thanks Everyone

Steve in NC

>Hey everyone

Thanks to all for the advice. It did not occur to me to shorten mt tool handles. Based on your comments, I think I will remount the mini lower and learn to turn small. (This may be the time to try my hand at mini HFs like Carol's.)