Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

My first hollow forms

Posts

My first hollow forms

#1

My first hollow forms

Bill Nichols

>This is my first attempt at making hollow forms. Ambrosia Maple ...both are about 3" dia. One is 5" and other is 3" tall. Comments please. Thanks for looking.


img

Re: My first hollow forms

#2

Brad Vietje

Re: My first hollow forms

Brad Vietje

>Way to go, Bill ! You're off and running. These are cute little guys, and I'll bet a lot of fun to make. Are they one piece, or is the rim/collar area attached ? Are you using a boring system, or hand-held tools?

Lookin good -- keep up the nice work.

Safe spinning,

Brad Vietje

Newbury, VT

Re: My first hollow forms

#3

Re: My first hollow forms

Bill Nichols

>One piece. Hollowed with ground allen wrench. Budget won't allow for hollowing rig. Hope to make one some day. Thanks for the kind words.

Re: My first hollow forms

#4

Re: My first hollow forms

Greg Haugen

>Bill, job well done! Nice pieces! Keep it up. Looking forward to seeing new pieces.

Greg

Re: My first hollow forms

#5

I will be...

Blake Washburn

>posting my first hollow from soon. It's in the finishing process. I just have to let it dry. I used sharpened Allen wrenches also. They're very handy. Anyway, great looking pieces.

Blake Washburn

Re: My first hollow forms

#6

Re: I will be...

Bill Nichols

>Thanks Blake. Looking forward to seeing your post. Wish I could have gotten started at 13 instead of 50 :)

Re: My first hollow forms

#7

Re: My first hollow forms

Bill Nichols

>Thanks Greg.

Re: My first hollow forms

#8

Re: My first hollow forms

gil jones

>Bill, you did nice work on your first hollow forms,

good looking wood too.

Gil

Re: My first hollow forms

#9

Re: My first hollow forms

Wayne Leach-NW Ontario

>Good job for your early attempt. I have not graduated to HF yet! I just love the looks of Ambrosia Maple in the photos I have seen and hope to get my hands on some one of these days.Just trying to catch up with posts after many hours of severe weather here in Americus,GA.

Wayne

Re: My first hollow forms

#10

Brad Vietje

Re: My first hollow forms

Brad Vietje

>Bill,

I mostly use hand-held tools, and only use the stabilized, captured, laser-guided setup for large pieces. For small and medium HF's I prefer the hand-held tools. I have made some Ellsworth-style hollowing tools, and I also have the small and large sets from John Jordan (see above reviews, etc...) His tools are very good. Michael Hosaluk also has some nice, simple hollowers.

BTW: I have not found the expensive alloy bits to be a great advantage on most woods, especially green or softer ones, so you might do well to make a set using larger Allen wrenches. If you heat them, you can also bend them to keep the cutting tip in line with the shft of the tool -- this helps a LOT. The fancy bits do help a lot with hard, dry woods, where the softer steels don't hold up long.

Safe spinning,

Brad Vietje

Newbury, VT

Re: My first hollow forms

#11

Re: My first hollow forms

Carole Valentine

>Now you gone and done it, Bill! Once you start doing those things, they are an addiction. These old eyes can't see a whole lot in the pic but they look like great first HFs but I can't quite figure out the necks from the picture. Are they curled back towards the body and hollowed out on the underside? If so you sure picked a tough form for your first!

Re: My first hollow forms

#12

Re: My first hollow forms

Bill Nichols

>Thanks Wayne. What brings you to Americus? Lots of Civil War history around those parts and not too for from the home place of a famous peanut farming woodworker. Bill

Re: My first hollow forms

#13

Re: My first hollow forms

Bill Nichols

>Thanks Carole. Yes the top rim is undercut. I've been following the design discussions on here for the last few months and although I didn't draw them out on paper like some suggest, I had a good idea of what I wanted to do when I started.