Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Lighting at Lathe

Posts

Lighting at Lathe

#1

Lighting at Lathe

eliot d

>I read on this site that florescent lighting is not preferred -- that incandescent is better. What about halogen? I use two of those lights that have those 500 watt pencil-shaped bulbs. It looks bright enough to me, but does it show up scratches as well as some other kinds of lighting?

Re: Lighting at Lathe

#2

Re: Lighting at Lathe

john lucas

>Elliot it should show scratches better than Fourescent. The best light to show scratches is a small point source set at an angle to the surface being viewed. Flourescent lights are very large in comparison and are usually in a fixed position so you can't move them.

A clear incandescent bulb or a small halogen bulb are the best. Most of us don't have that so we go to the next best, which is a standard house hold bulb of 100 watts or so. The quartz lights would be almost the same but of course brighter and hotter. Moving the light further away makes it more of a point source but then you can't move it around.

I like a light that's close enough I can move it around to get more of an angle on the surface. This will vary of course depending on shape. That's why I like the Moffet lamps. They are easy to move and don't get too hot to the touch. The next best thing is the industrial quartz lamps with goose necks and magnets. If they have a good insulated houseing so you don't burn your fingers then they are excellent.

Re: Lighting at Lathe

#3

JL

Re: Lighting at Lathe

JL

>On my old lathe space I have track lighting. I'll be putting up track lighting in my new lathe space one of these days (hopefully before I move the lathe).

I did put up one set of track lights in the new space. I am using the PAR 30 65 watt bulbs.

If you put the track parallel with the lathe, you can rotate the fixtures so you effectively illuminate both sides (of spindles that is).

Re: Lighting at Lathe

#4

Re: Lighting at Lathe

Bill Hale / Woodspinner

>I use a 500 watt halogen mounted on the ceiling and 2 ceiling mounted reflectors with 100 watt inc. in each. I also have a floor stand that I can move around with a 500 watt halogen in it. I use this one primarily to see inside bowls when turning the inside.

NOTE OF CAUTION--- When using the halogens they get very hot so remove the wire guard from the front. I had the experience where some shavings got hung on the guard and started to burn. They were droping on the floor with the other shavings when I saw them. I got it out prior to any real flames !

One thing I do to keep electric cost down is all of my lighting is on X-10 switches and when I don't need them I just hit a button and they are off.

Good turning and be safe

Bill in Casa Grande, AZ.

Re: Lighting at Lathe

#5

Re: Lighting at Lathe

Russ Fairfield

>The halogen light will work fine, but at 500-watts you might need to wear sungtlasses to keep from frying your eyes. You might want to back off to a lower wattage.

Re: Lighting at Lathe

#6

Roger Dunn

Re: Lighting at Lathe

Roger Dunn

>If you can find a used dentist's light with the movable arm, you won't be disappointed!

Re: Lighting at Lathe

#7

Re: Lighting at Lathe

Don in Central Illinis

>I just got won a few weeks ago, but haven't had time to put it up yet. Maybe this weekend. If I get it up, I'll post and tell everyone if it is worth the hassle.

Re: Lighting at Lathe

#8

Re: Several 500w lights would heat the shop!!

Jamie Donaldson

>

Re: Lighting at Lathe

#9

Re: Lighting at Lathe

Larry In Lima

>I am putting up track lighting for my lathe in the next couple days. Makes it very nice. I have already done my grinding workbench area, with drill press, and it's great. Very illuminated, adjustable, etc... Larry

Re: Lighting at Lathe

#10

Re: Lighting at Lathe *LINK*

Bob Fawcett

>I use both halogen and flourescent. I have some flourescents on the ceiling for general illumination and 2 halogens I can move and aim where I like.

The box stores have clamp on gooseneck lamps that are inexpensive, but my favorite is this architect desk lamp.


img

Architect desk lamp

Re: Lighting at Lathe

#11

Re: Lighting at Lathe

rj anema

>Be very careful with that architects lamp as the outer metal housing gets very, very hot. I know!!

Re: Lighting at Lathe

#12

Dick Hines

Re: Lighting at Lathe

Dick Hines

>Be careful with halogen lights. I have 2 hanging from my roll up door frame. The other night I was turning a HF and was not paying any attention where the lights were. The next thing I knew was my head got hot. Real HOT!!

Of course most people would not be tall to have this happen to them.

Re: Lighting at Lathe

#13

John, do you know of any small higher intensity

Don Henthorn

>LED lights that would be good for this purpose?

Re: Lighting at Lathe

#14

Re: John, do you know of any small higher intensit

john lucas

>I think we will definitely see some led lights used for this in the future. I haven't looked for a light for that purpose. I'm teaching a turner today so I'll take my LED light out there and try. I have a large one that has 6 LED's and a small one with one LED. I don't know which would be the best but I'll let you know the results.

Re: Lighting at Lathe

#15

You need more hair :)

john lucas

>