Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Beal Buffing question

Posts

Beal Buffing question

#1

Beal Buffing question

Dennis Taylor

>I have the Beal Buff, I use it now on smaller objects without a problem, mine is with the adpater to a motor shaft, problem is when I try to use it on platters or bowls, it isn't deep enough between the end of the shaft and the top the motor sits on, I have looked at the Packard site, and don't see any item to extend out the lenght, anyone else had this and combated it?...tks in advance...Dennis

Re: Beal Buffing question

#2

Re: Beal Buffing question *LINK*

Mike Cunningham (Cape May NJ)

>I have an 8" extension that I bought from Craft Supply. See the link

Mike


Beall extension from CS

Re: Beal Buffing question

#3

Re: Beal Buffing question

john lucas

>I use the Long Buffing adaptor $29.95 from Craft Supplies. It's 8" long and works really well. You can also use a Morse taper extension that you also can get from Craft Supplies for $15. It's about 3 1/2"

Re: Beal Buffing question

#4

Re: Beal Buffing question

Dennis Taylor

>I don't use the Beall on the lathe, but off on a motor, 1725rpm, so the adapters from CS or Packard all seem to extend the piece from the lathe headstock, not from a motor mount...the hub adapter that comes with the Beall is for a 1/2 or 5/8 motor shaft, and it works fine, except for the length, I need to increase that length...hope this makes sense...Dennis

Re: Beal Buffing question

#5

Re: Beal Buffing question

Mike Cunningham (Cape May NJ)

>I believe that I understand. What I don't understand is why Beall would supply a hub adapter for use on a motor but not an extension for use on that same adapter. First, I'd call Roger Durst at Craft Supply 1-800-398-2743, if that doesn't work try Beall directly, failing all of that I'd be off to the hardware store and/or electric motor shop to find parts to rig something or possibly a local machine shop.

Re: Beal Buffing question

#6

Re: Beal Buffing question *LINK*

Russ Babbitt

>Here is the extension from Beall that will fit you motor.


Beall Tools

Re: Beal Buffing question

#7

Re: Beal Buffing question

Dennis Taylor

>Russ thanks, I think that is the beast that I am looking for, just need the length of the adapter longer and that should about fit the bill...tks...Dennis

Re: Beal Buffing question

#8

Re: Beal Buffing question

bowlman

>Looks to me like you could buy 2 ... screw 1 into the other for a 6" extension. Yes, no?

Re: Beal Buffing question

#9

Re: Beal Buffing question

john lucas

>looks to me like you could but you could 8" of extension with the othere adaptor I mentioned.

Re: Beal Buffing question

#10

Paul Porter

Try Don Pencil *LINK*

Paul Porter

>I have one of his 8 inch adapters. It works great.

No affiliation, just a satisfied customer.


Don Pencil's Website

Re: Beal Buffing question

#11

Re: Beal Buffing question

Dennis Taylor

>That is a good question, with the 3 3/4 inch length of the supplied hub to motor shaft, if I added 2 more at 3 inches, that wwould increase the lenght to 9 3/4 that the wheel would stick out from the motor, and give me room to buff larger bowls and platters, anyone think this would work?....the 8 inch long adapters are for the lathe headstock, and I would rather use the motor, only because I am already set up with the motor and buffing type station...maybe the 2 3in would work with what I have, plenty of reach then?...what do you think?...Dennis