Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Splash! The plunge

Posts

Splash! The plunge

#1

Splash! The plunge

David Breth

>I caved in to a new lathe over the weekend. Well, new to me anyway. Last week I missed a Jet 1236 that was unused in the box for $300. That planted a "gotta upgrade from the mini now" bug in me, and I found another 1236 for $325 that was pretty lightly used (made in '98). The benefit in this unit versus the other is that I was able to verify that all was in working order, and that the tail and headstock lined up - dead on. Plus, I bought something in an antique store two weeks ago for $18, and sold it on Ebay for a little over $100 to help with the lathe, meaning that I've got $240 in the lathe rather than $325.

I don't know how I did it without killing myself, but I got it in the basement and set up last night. Basically, I tried to take it slow, and allowed objects other than me to bear the brunt of leverage. Next will be to figure out how to arrange the dust collector to support between centers and outboard headstock positions....

It is decision time with respect to my mini (a Fische). Keep or sell. I'm thinking sell because of space (very small shop), plus what would I need it for at this point? There's no reason I couldn't do small work on this larger lathe (such as pens), is there?

David B.

Re: Splash! The plunge

#2

Re:OOooohhh David - you're cooked now!!!

Jamie Donaldson

>Soon there will be a need to turn larger bowls, so a lathe with a larger swing capacity, then a short bed stud lathe for hollowing, then.............

Re: Splash! The plunge

#3

Re: Splash! The plunge

Mike Cunningham (Cape May NJ)

>David,

For your dust collection setup. First, I'm sure that you know that it will only grab sanding dust and not shavings from cutting. I have one of those large hoods, I got mine I believe from Penn State. I mounted it to one of those telescoping tripod leg deals used to hold a halogen shop/work light. I can adjust it's height and position from the headstock. I ran my DC collection pipes beneath my shop floor and I attach this with a flex hose to a pipe and blast gate that come though the floor at the lathe. When not in use I simply disconnect the flex from the pipe and move the entire thing.

As for selling your mini, hold off. Jamie's right, you'll find excuses errr I mean valid reasons to have several lathes. I have a 3 hp shortbed VL300, a VL100 (Rude Osolnik was the previous owner)and now find that I "need" another full size lathe and I'm in a search for an old General, Jline, etc in need of a restoration, TLC and new home.

Have fun!

Mike

Re: Splash! The plunge

#4

Here's the DC setup

Mike Cunningham (Cape May NJ)

>Hopefully this photo is of a size and quality to give an understanding of what I was describing.

Mike


img

Re: Splash! The plunge

#5

Re: Splash! The plunge

Brodie Brickey

>David,

Congratulations on your purchase. If you do a lot of pen turning, you might keep the Fisch or if you want a lathe for sanding outside the shop (so you don't have to clean up as much).

Other than that, get it out of there and buy some other new tools to go with the new lathe.

Regards,

Brodie

Re: Splash! The plunge

#6

Congrats and a warning and a suggestion

GaryG in MD

>David,

Congrats on your "new" Jet 1236. I believe it will serve you well.

I've had only one problem with mine, and that's with an accessory -- do NOT use the banjo 'extender' for any reason, inboard or outboard. Throw it awa or use it for a paper weight. It WILL break in half and fall on the floor. It's not a matter of "if"; ...

(See www.woodcentral.com/cgi-bin/archives_turning.pl?read=74371)

If you're lucky, that's all that will happen, but it could lead to a dangerous situation.

You will want to get a MT2 - MT2 morse taper extender. For many situations, you will find that there is not enough room between the headstock and tailstock to maneuver the tool rest banjo into a needed position. With the extender in the tail stock, this problem goes away. I have Gary Evans to thank for that tip. (Thanks again, Gary)The one I got [Craft Supplies part# 251-0200] has a 3.5" barrel and is slightly under 7" overall. I don't think you would want a longer one. I have had no problem with vibration when using this with reasonably balanced loads. Your live center will get stuck in it. Unless you want to devote a live center to it permanently (I wouldn't recommend it), you'll find that you can tap it out diagonally through the slot with a flat-end center punch and hammer.

Enjoy your new toy! ...Gary

Re: Splash! The plunge

#7

Re: Congrats and a warning and a suggestion

Bob Fawcett

>Morse taper adapters have that slot so you can use a wedge to remove the center. If you didn't get one with the adapter, you can make one. You need a piece of mild steel (HD or Lowes) about 3/16" thick by 1/2" wide or so. The size should fit through the slot. Make a long diagonal cut across one end to form the wedge. Insert the pointed end behind the center and tap the other end with a hammer. Your center should pop right out.

Re: Splash! The plunge

#8

Re: Congrats and a warning and a suggestion

David Breth

>Bob/Gary - thanks for those tips. I was expecting to get an extender as you suggest, but there's no way I would have thought of the banjo deal.

David B.