Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

My first Scoop

Posts

My first Scoop

#1

My first Scoop

Dominic Greco in Richboro PA

>Hello Everyone,

Here's my first attempt at turning a scoop. I'm actually a little surprised at how much work went into something so easy looking! It's like turning a goblet, complete with deep hollowing the "vessel" portion.

Since this was my first, I used whatever wood I had on hand. I ending up using a 3" sq x 8" long piece of walnut I had laying around.

I sanded it to 320 grit on the lathe, bandsawed out the profile, and then cleaned up the cuts on my belt/disc sander. Then I just hand sanded the entire thing to 400 grit. I probably could have stopped at 220. But I just couldn't bring myself to! Weird, eh?

The finish is several coats of Mineral Oil followed by buffing with Tripoli Compound, then a coat of bee's wax, and more buffing.

I initially turned this scoop in preparation for making one for my Mom. When I showed it to my wife she said, "This one's for me, right?". And without batting an eyelash I said, "Yes. Yes it is." :>)

I think the next scoop I turn will be longer and deeper in the "scoop" portion. But Iguess it depends on what you want to use it for. My Mom wants it for flour, sugar, and other baking goods.

I'd also like to ask a "procedural" question about hollowing scoops like this.

After turning the exterior profile of the scoop portion between centers, I turned a tenon on the "handle" end. I removed the spur center and replaced it with my talon chuck. After it was installed in my chuck, I started to hollow it. Or tried to. I ended up getting a slight catch and knocking it off center. At that point I broke out the steady rest and hollowed the remainder of the scoop. After I finished the hollowing, I removed the steady rest and sanded the scoop interior. I then brought my tailstock up and used a wooden bull nose (with a piece of 400 grit sandpaper wedged between) on my live center to hold it in place while I turned the handle.

Does this sound like too much work? Or am I doing it correctly?

Thanks for viewing

See ya around,

My ugly mug

Dominic


img

Re: My first Scoop

#2

Pic#2 

Dominic Greco in Richboro PA

>


img

Re: My first Scoop

#3

Re: My first Scoop

gil jones

>Cool!!

Re: My first Scoop

#4

Re: My first Scoop

Phil Joines Krum, TX

>Interesting shape. I like the way the back comes up rather than being cut flat across.

There are two things I do differantly. Use the steady before the catch :>) and drill most of the interior out with a Fostner bit.

Re: My first Scoop

#5

Re: My first Scoop

Tom Libby

>Great finish and shape!

Re: My first Scoop

#6

Re: My first Scoop *LINK*

Darrell Feltmate

>Nice scoop. Boy you like to work hard :-) Try this procedure.

1) turn a tenon for your chuck first and mount in a four jaw chuck

(a good screw chuck will work too)

2) do the inside of the bowl and sand it

3) turn and sand the outside of the bowl

4) turn and sand the handle

5) part off

6) angle the bandsaw table about 20*

7) cut off the side

8) shape the side of the scoop on the belt sander

9) do any hand sanding necessary

10) finish

I am almost inspired to turn a few more of these. The last time I turned scoops it was for a woman who makes specialty soaps and she wanted a bunch for some gift baskets that included bath salts. After the first 50 I was not that impressed with turning scoops unless it was someone else turning ;-)


Around the Woods

Re: My first Scoop

#7

But Can You

Jim Shaver Oakville, Ont.

>get two scoops of rasins in that?

A sweet lovely looking scoop Dom,

Well done..

Take care,

Jim

Re: My first Scoop

#8

Thanks everyone!

Dominic Greco in Richboro PA

>