Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Tail Stock, Rockwell Lathe

Posts

Tail Stock, Rockwell Lathe

#1

Tail Stock, Rockwell Lathe

HeatherA in Alaska

>Hello, I finally got some lathe time in this week on my new (old) Rockwell lathe (46-450). I reluctantly pulled up the tail stock (with the new Oneway live center) to the spur center. I say reluctantly because I had forgotten to do this before I bought it and was afraid they would not line up. I was VERY happy when as Jimmy Clewes said they were "spot on". My issue is with getting accessories out of the morse taper on the tail stock. I had to dismantle it to get the oneway out, take out the tailstock, put in a rod (aka drill bit) that fit and knock out the center. I am used to my Jet mini that is self ejecting. Am I missing something? Can I make some cylinder to fit into the tailstock assembly that would make it self ejecting? As it is now, the spindle bottoms out before it hits the center end.

Thanks,

Heather

Overcoming one hurdle at a time! (That might be my new life quote)

Re: Tail Stock, Rockwell Lathe

#2

Re: Tail Stock, Rockwell Lathe *LINK*

gil jones

>From the diagram it looks like no hollow tailstock spindle on that lathe. Found the link info here >> http://www.acetoolrepair.com/DeltaHtml/Tables/WoodLathes.htm

I suspect that you will ruin the live center bearings if you forcefully knock it out of the tailstock spindle every time. Maybe a very good cleaning (or finish reaming) of the spindle(s) Morse tapers would help.


http://www.acetoolrepair.com/DeltaHtml/WL/WL3B.htm

Re: Tail Stock, Rockwell Lathe

#3

Re: Tail Stock, Rockwell Lathe

Phil Joines Krum, TX

>Not all Morse Taper shanks are the same length. Wind the spindle back and check the depth to the rod. Compare that length to the part Oneway that actually fits into the swallow. If the Oneway's shorter make up a piece to fill the extra space. It the length is the same or the center is longer the swallow probably needs a serious cleaning and maybe beburred. There are #2MT hand reamers available but one may not work if the spindle is hardened.

Re: Tail Stock, Rockwell Lathe

#4

Re: Tail Stock, Rockwell Lathe

Barry Irby

>Is the quill supposed to be self ejecting? Not hollow for a knockout bar? Try looking at he quill (30) and the quill adjusting screw (31) in the parts list in the link above. Can the quill be adjusted to eject you center?

Re: Tail Stock, Rockwell Lathe

#5

Re: Tail Stock, Rockwell Lathe

Peter Hyde

>I have the same tailstock assembly on my Delta and I just place the handle of a wrench between the back of the live center and the tailstock casting and unwind the quill. The live center just pops out.

Re: Tail Stock, Rockwell Lathe

#6

Re: Tail Stock, Rockwell Lathe

Bob Fawcett

>On industrial drill presses they use a morse taper to hold the bits. These have slot that goes across the quill. You put a metal wedge through the slot and tap with a hammer. This knocks out the bit.

Is it possible that the old Rockwell is designed this way??

Re: Tail Stock, Rockwell Lathe

#7

Re: Tail Stock, Rockwell Lathe

HeatherA in Alaska

>Thanks for the replies. I got an email for a suggestion similar to Peter's. I put a block of wood between the live center and the tailstock and then backed it out. Worked like a charm!

Heather