Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

How to finish?

Posts

How to finish?

#1

How to finish?

Dave Belser

>I'm attempting to fulfill a request to turn a bowl from a pine burl. I know that this is a less than desirable wood to attempt to turn, but this is also my first attempt at turning an burl bowl of this type. I told the person that the wood might not be worth the effort but that I'd give it a try.

And so it goes..... I spent quite a bit of time picking the bark off of the outside, found mounting and balancing it enough to turn to be a little challenging - but I'm actually reasonably pleased with the results so far.

I knew that sanding and finishing would be difficult. This wood is so full of pitch and resin that dry sanding is out of the question. I've been using danish oil to wet sand that's working out good. I'm not thrilled by the way the oil dulls the contrast and yellows the wood - but I suppose that this will happen in the long run anyway.

The question is (two actually) is there anything else I could wet sand with that would be better? AND how/what do I use for a final finish?

I'm afraid that the pitch and/or oil will always leave a finish that feels tacky. Is there anyway to "seal" wood this pitchy and end up with a satin feel?

Knowledge and experiences much appreciated.

- Dave


img

Re: How to finish?

#2

Re: How to finish?

Ken

>Here is a pine burl that was very dry when I turned it. Had no problems at all. Stopped where I did because the "fish" appeared and didn't want to lose it.

Gave it a coat of clear Danish oil and then 3 coats of wipe on poly sanding with 220 between coats. Beall buff as a final finish.

Ken


img

Re: How to finish?

#3

Re: How to finish?

George Van

>Dave, I have had good results with shellac for sealing the pitch in knots, I would think that it would also work on a burl but have never had the opportunity to try it.

Re: How to finish?

#4

Re: How to finish?

Bill Hunt

>Try mineral oil, I had a fellow who turned bowls from "lighter knots" tell me that it helped prevent the gumming up on sandpaper. Those of you not from the South may not be familiar with "lighter knots"

Re: How to finish?

#5

Re: How to finish?

Travis Stinson

>I talked to a guy at a show last year that had turned a Pine burl, it looked great. He told me the secret to preventing the paper from clogging was to wet sand with olive oil.

Re: How to finish?

#6

Re: How to finish?

Ralph Watts

>After you get finished sanding, coat the entire piece with shelac. The 'resin will bleed forever and keeps most finishes from drying. This is based on my turning a 12" disk from a very large pine burl and having experienced checking on an earlier piece. I also coat with shelac when I finish sanding an area-sometimes the turpintine evaporates so fast that thin sections will crack.

Regards, Ralph

Re: How to finish?

#7

Re: How to finish?

stacey s

>Is that like fat lighter. I have only ever seen it as old pieces of trunk and stump in the woods around here(South Ga) is this the same?

Re: How to finish?

#8

Re: How to finish?

Allen Neighbors

>Dave, Shellac is good for stopping the pitch dead in it's tracks. But I would thin the Shellac about half and half the first time, then coat the knots. A couple of times should fix the problem.

Not sure, though. I've never turned a burl of pine. Others will probably know a lot more than I do about it.

This is just what I would do if I didn't know better. :o)

Re: How to finish?

#9

Thanks

Dave Belser

>For all the good advice. Looks like I can use just about any oil for sanding - I'll probably use mineral. Then I'll finish with shellac.

Again, thanks for all the good advice.

- Dave