Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Old rockwell lathe, T Daniel ?

Posts

Old rockwell lathe, T Daniel ?

#1

Old rockwell lathe, T Daniel ?

HeatherA in Alaska

>Hello all, I finally got my new Rockwell 46-450 12" gap bed lathe moved into the garage. Terry (and of course anyone else), you mentioned on the classified forum that there are some modifications you would make to these lathes. Any suggestions? The bottom belt seems loose but it goes through all the speeds without trouble. Does anyone use the offset tool rest extension or the gap filling block? I do not have these but have seen them for sale. I just ordered a oneway live center for it as a welcoming present. I can't wait to get it up and running but right now we are fighting the clock to get winterized.

Thanks,

Heather

Re: Old rockwell lathe, T Daniel ?

#2

Re: Old rockwell lathe, T Daniel ?

John Lucas

>I always hated a gap bed so If it was mine I would buy the gap filler and put in and probably never remove it.

Re: Old rockwell lathe, T Daniel ?

#3

Re: Old rockwell lathe, T Daniel ?

TDaniel

>some mods: If you have trouble with the banjo and toolrest locking and staying where you put it check with One-way about a replacement. I replaced the banjo and toolrest on my Vicmarc VL300 with the One-way banjo and it made all the difference in the world with this otherwise good lathe. Electronic variable speed would also be nice but you might get by with a jackshaft to get lower speeds. You might check to see if anyone has put riser blocks on this model lathe. If you plan to do that then do it before ordering a new banjo.

Re: Old rockwell lathe, T Daniel ?

#4

T Daniel ?

Mike Cunningham (Cape May NJ)

>I'm not trying to hijack this thread. In fact I'm looking for an old Rockwell and that prompted my interest in reading the replies.

I am curious about something. I too have a VL300 and wonder why you felt a need to replace the banjo?

Thanks,

Mike

Re: Old rockwell lathe, T Daniel ?

#5

Riser Blocks headstock

Phil Joines Krum, Tx

>I added risers to SWMBO's Delta. I don't know what the wood is, very dense. The pieces are all cut on the table saw and the end grain is vertical. Threaded rod was used to make the longer bolts.


img

Re: Old rockwell lathe, T Daniel ?

#6

Re: Riser Blocks tailstock

Phil Joines Krum, Tx

>There is a piece of sheet metal connecting the riser and the tailstock casting. They kept sliding against each other. There's also a piece of brass shim stock under one side of the riser and attached to it with screws to bring the centers into alignment.


img

Re: Old rockwell lathe, T Daniel ?

#7

Re: Riser Blocks tailstock

Phil Joines Krum, Tx

>These are the replacement parts for the tailstock lock. Made with off the shelf hardware.

I replaced the banjo with one for a Nova 3000, $90 from Woodcraft at the time(2003 or 4). The tool rests are home made with lonker shanks.

The motor was replaced with a 2HP VS from Dealers Electric. The pully is a single step, the smallest I could find. To vary the pully ratio the belt is moved to whatever spindle pully works. The misallignment in the link belt due to the pully offset doesn't seem to bother anything.


img

Re: Old rockwell lathe, T Daniel ?

#8

Mike....

TDaniel

>When I lock a banjo in place I don't want it to move. I turn a lot of natural edge burls and each piece of wood may cost a couple hundred bucks. I don't want the banjo or toolrest moving, possibly hitting the natural edge of the burl and destroying it. I had to replace the handle on my Vic with a bolt and a box-end wrench to get it tight enough so that it did not move. That created another problem, the shaft of the toolrest became heavily marked by the extra pressure and that had to be filed off frequently to keep the post round. Now that I have converted to a One-Way banjo and toolrest I just press the lever down and nothing moves. To me the heart of a lathe is the banjo. The banjo gets moved more than anything else on a lathe so it has to lock down tightly with minimal effort. I brought this to Victor's attention in Orlando but he didn't seem to think it was a problem.

TD

Re: Old rockwell lathe, T Daniel ?

#9

Thanks Phil

OB O'Brien

>Thanks Phil for the pictures and explanations. I have been considering doing this to mine. I have a VFD for another lathe so all I would need to do is build the riser blocks and add a 3 phase motor. Did you remove the reeves drive or just use that with the VFD?

Thanks again OB

Re: Old rockwell lathe, T Daniel ?

#10

Re: Thanks Phil

Phil Joines Krum, Tx

>This lathe didn't have a Reeves but if it had I would have removed it. IMHO they are a maintance problem and unreliable.

Re: Old rockwell lathe, T Daniel ?

#11

TD

Mike Cunningham (Cape May NJ)

>Thanks for the reply. I haven't had any movement issues with mine, I've had it about 2 years. However thanks, I'll keep a careful eye on it.

Re: Old rockwell lathe, T Daniel ?

#12

Re: Old rockwell lathe, T Daniel ?

HeatherA in Alaska

>Thanks for all the replies. I turn mostly smaller stuff so I think I will try it as is and then see if I need to make any changes.

Heather