Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Question for Dave Smith

Posts

Question for Dave Smith

#1

Question for Dave Smith

Phil Joines Krum, Tx

>Dave,

In your article �Friction Polish for Turning� you say �equal parts boiled linseed oil, pale shellac and alcohol�.

Are you referring to premixed shellac? Do you have any idea what the shelf life might be?

I want to make some using super blond flakes I have on hand.

Re: Question for Dave Smith

#2

I guess that would be me.

Dave Smith, Longview, WA

>Hi Phil,

I use shellac made from flakes. The premixed stuff had too much wax in it for my liking. I prefer pale shellac flakes. For light colored wood I use tung oil instead of linseed oil. Mix in small batches and shake well before using. If you leave the lid off overnight it might get a little thick. DAMHIKT

Be sure to grasp the bottle top and bottom between you thumb and finger before shaking. Or, make sure the cap is screwed on before shaking. DAMHIKT

Good luck.

Dave Smith

Answers are free, correct answers cost twice as much in Longview, WA.

Re: Question for Dave Smith

#3

Re: I guess that would be me.

gil jones

>Dave, I suspect that Phil's question is similar to mine.... Is the 1/3 portion of shellac in a state of "already mixed w/alcohol and usable as is" or is the 1/3 portion of shellac in the form of dry flakes? To me this is a valid question, as pre-mixed shellac can be in many different strength ratios.

Thanks,

Gil

Re: Question for Dave Smith

#4

Brad Vietje

May I refine that question?

Brad Vietje

>Quick, quick, before we have to pay twice as much for the answer...

Dave -- is that 1/3 dry flakes by weight, or 1/3 part a ???-pound cut of freshly mixed liquid by volume ?

Safe chemistry,

Brad Vietje

Newbury, VT

Re: Question for Dave Smith

#5

Same Question, different format..shrug..

gil jones

>

Re: Question for Dave Smith

#6

Let's try again

Dave Smith, Longview, WA

>Friction polish mix equal parts:

2# cut pale shellac(shellac flakes dissolved in alcohol)*

linseed oil (tung oil for light colored material)

denatured alcohol

I recommend mixing 1 fluid ounce of each ingredient for a batch. Three ounces of friction polish goes a long way and is a lot less to clean up when you shake the bottle with the lid unscrewed.

* - From the Hock Finishes web page

"Two-pound-cut" describes two pounds of Shellac in one gallon (32 ounces in 128 fluid ounces, or 1 ounce of flakes in 4 ounces of alcohol) of alcohol. So to achieve a two-pound cut in a half-pint of alcohol, you'd mix 2 ounces of flakes, by weight, with 8 fluid ounces of alcohol.

Dave Smith

I think I understood what I meant in Longview, WA.

Re: Question for Dave Smith

#7

Re: Let's try again

Phil Joines Krum, Tx

>If I understand it's

1/2 oz.(weight) flakes disolved in 2 oz.(volume) alcy to make the 2lb cut

2 more oz alcy

2oz oil

Total mix is 6+ oz.

Flavor to taste :>)

Re: Question for Dave Smith

#8

Dissolve shellac in alcohol separately for 2# cut

Dave Smith, Longview, WA

>After the shellac flakes have dissolved mix equal parts of the 2# cut shellac, linseed oil and denatured alcohol.

In my first response I said, "I use shellac made from flakes". I thought it was self explanatory that the shellac was already dissolved in alcohol. Most people make a 2# cut for use as a finish.

Dave Smith

That's my story and I am sticking to it in Longview, WA.

Re: Question for Dave Smith

#9

Re: Dissolve shellac in alcohol separately for 2#

Phil Joines Krum, Tx

>Dave,

Do you use hardware store alcy or something a bit purer? I�m thinking of using Everclear but it�s a 20 mile drive to get it.

Re: Question for Dave Smith

#10

Use denatured alcohol. *LINK*

Dave Smith, Longview, WA

>You can use everclear if you want to pay the tax on ethanol. I have listed 4 brands of denatured alcohol with high ethanol content on my alcohol soaking blog. As most people know I don't recommend using products high in methanol. Methanol is bad doo doo.

Some people recommend dry alcohol for dissolving shellac flakes. It is extremely difficult and expensive to remove the last 5% of water that is left after distillation. That is why everclear is 190 proof or 95% alcohol. Since alcohol will readily absorb moisture from the air I am not sure spending the extra bucks for anhydrous or water free alcohol is worth while. For friction polish just use hardware store variety denatured alcohol.

Dave Smith

I hope this polishes off the answer in Longview, WA.


Alcohol Brands

Re: Question for Dave Smith

#11

Re: Dissolve shellac in alcohol separately for 2#

Bill White

>EVERCLEAR? You'll blow the shop with that stuff. 'Course you can drink the leftovers. Does that make the shellac taste any better?

Bill

Re: Question for Dave Smith

#12

Re: Yes, you can tell the difference.... *LINK*

Russ Fairfield

>.....because THERE IS A DIFFERENCE. The less water in the initial solvent the harder the shellac finish, and the less likely it will be damaged by water or body oils later. Whether that difference is worth the difference in price depends how long we want the finish to last.

My article on shellac, linked below, and the following article (#10) on friction polishes might be useful.

There is also an article in the Wood Central archives by Jeff Jewwett thaqt should be a "Must Read" for qnyone using shellac.


Shellac

Re: Question for Dave Smith

#13

Re: Link to Jeff Jewett shellac article *LINK*

Russ Fairfield

>This is a must read for anyone using shellac.

There are a total of 51 other articles here on Wood Central on the subject of shellac.

You folks are missing out on a wealth of informationb on a lot of topics by not using the search function available on the front page of Wood Central. Ellis and a lot of volunteers make these articles ans other information available. Their's is a wasted wffort if nobody uses it.


http://www.woodcentral.com/articles/finishing/articles_173.shtml

Re: Question for Dave Smith

#14

Re: Dissolve shellac in alcohol separately for 2#

Phil Joines Krum, Tx

>I used it for the finish on music instruments when I could hear well enough to make them. Never had a problem.

One for you, One for me............