Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Spearpoint ?? Tool

Posts

Spearpoint ?? Tool

#1

Spearpoint ?? Tool

Tom Minehan

>I have come upon a tool that I believe to be a spearpoint something or other. The tool comes to a 70 degree point like a spear and the bevel on the side of each point is about 40 degrees. What is such a tool used for and do the bevels sound about right? I haven't seen anything like this advertised.

Re: Spearpoint ?? Tool

#2

Re: Spearpoint ?? Tool

Allen Neighbors

>I think you just described a Parting Tool, which is used for separating the turned piece from the rest of the wood.

Re: Spearpoint ?? Tool

#3

Re: Spearpoint ?? Tool

Hooligan

>There's also a possibility that it is a spearpoint scraper. I use them a lot for small v-grooves, and shear scraping tight angles, such as around the foot of a bowl.

They are a great tool.

Re: Spearpoint ?? Tool

#4

Re: Spearpoint ?? Tool

gil jones

>Do you have a pic?

Re: Spearpoint ?? Tool

#5

JL

Re:Raffan has a tool like that

JL

>Don't know if this is it. Post a pic.


img

Re: Spearpoint ?? Tool

#6

Re: Spearpoint ?? Tool *LINK*

Hooligan

>Gil, I don't have a pic, because I am just too lazy to go get it, and take one. BUT, here's a link:


Raffan's Spear point

Re: Spearpoint ?? Tool

#7

Re: Spearpoint ?? Tool

Wally Dickerman in Arizona

>I bought a set of Greenlee tools about 50 years ago that had a spearpoint tool. In those days most sets had one. I still use it on occasion. Groove cutting, light scraping in tight places, and more. I still have a couple of other tools from that set that have been ground for special uses. I hardly ever throw a tool away. That's why I have over 40 of them.

Wally

Re: Spearpoint ?? Tool

#8

Re: Spearpoint ?? Tool

John Lucas

>My best friend is an expert with this tool and uses it a lot. Many of the ways he uses the tool are similar to the way I use a skew with the toe down. You can cut grooves in a scraping mode and hold the handle high and use the top edges in shear scraping mode. Randy uses the top as a bevel and cuts end grain for the bottom of candlesticks and goblets. He also rides the short bevels and uses the tool to "tuck in" sharp details like those between a goblet top and stem. It is a very handy tool in the hands of a master like my friend Randy. When I point out that he uses it like a skew he just tells me he never did learn to use the skew.

Re: Spearpoint ?? Tool

#9

Re: Spearpoint ?? Tool

Tom Minehan

>Thanks for the help!! It does look like Raffan's except to me it looks like the bevel on his is more like a scraper's and mine looks more like a spindle gouge's. With Wally's clue I find mine came from a "Craftsman" set of some unknown vintage. I will play with it tomorrow and see what it does.

Re: Spearpoint ?? Tool

#10

Re: Spearpoint ?? Tool

RobinCorell

>A spear point held perpendicular to the center line can be real handy around a stuborn knot or an irregular edge. used like this it leaves a really poor quallity surface, almost like the threads on a fine screw. Following with a light pass with a round or square nosed scraper with a negative rake will clean things up nicely. This is how patternmakers typically turn.

I think I might have the twin to Wally's set of old Greenlee tools. Nice heavy old things. I still prefer the 1 1/2" roughing gouge from that set to the point that I use it for about 70% of the lathe work I do.

Robin

Re: Spearpoint ?? Tool

#11

Diamond Point *LINK*

Mike Brazeau

>Tom - is it like the diamond point tool third from the bottom of the page at this link? Sharp point with two edges undercut severely. I have one that came with a set of carbon steel Delta tools with a Rockwell Homecraft I bought used in 1970. Dates from the late 50's. Haven't used in years, but did use for cutting of nibs and such at one time or as a scraper for grooves.

Mike


Ashely Iles

Re: Spearpoint ?? Tool

#12

Re: Spearpoint ?? Tool

Barry Irby

>I have a set of Craftsman tools I bought about 40 years ago when I was a kid. It had a diamond point tool in it and I still have it. I don't really know what it is specifically for. I have used it like a scraper to create beads.

Re: Spearpoint ?? Tool

#13

Re: I also started with Greenlee...

JamieDonaldson

>... carbon steel set, but don't use them much since HSS came along.

Re: Spearpoint ?? Tool

#14

Randy's spear point tool

john lucas

>Here is a photo of the tool. It's pretty thin, maybe 1/4". The angles make about a 90 degree point when you look at the top.


img

Re: Spearpoint ?? Tool

#15

Re: Randy's spear point tool in use

john lucas

>Here it is in use. He uses the flat side as the bevel in this instance cutting the back side of that bead and down to the bottom, mostly to clean up the bottom and to finalize the shape of the bead or curve. I don't have a photo of him riding the short bevel. He does that also. Used with the flat side as the bevel it is great for cleaning up the endgrain on the bottom of goblets and candlesticks.


img

Re: Spearpoint ?? Tool

#16

Re: Spearpoint ?? Tool

Tom Minehan

>Thanks again for the responses. I now have a good idea on what the tool is and how to use it. It was part of a 5 piece set of Craftsman tools from the late 60's 0r 70's. (I now have the other 4 pieces.)

Re: Spearpoint ?? Tool

#17

Re: Spearpoint ?? Tool

Ed Karch

>Outside texture done with a spearpoint tool.


img

Re: Spearpoint ?? Tool

#18

Re: Spearpoint ?? Tool

Allen Neighbors

>Ed, that's cool! Pretty wood, too. Wish I could see a straight-on side shot. I might have to try something like that.

Good job.