Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Drying question from a newbie

Posts

Drying question from a newbie

#1

Steve Kubien

Drying question from a newbie

Steve Kubien

>Evening everybody,

I am nearly finished building a lathe similar to the plans in Shop Notes a couple of years ago. Since I've never turned I though I would try this low-cost option to see if I will even enjoy it. With that in mind I came across some maple which had been trimmed by a neighbour and decided to bring home a bit and dry it out for use once the lathe is done. I was cut today and I slapped a bunch of latex paint on the ends to limit the checking while it dries. Did I do the right thing or am I just making colourful firewood?

Thanks for your help,

Steve Kubien

Re: Drying question from a newbie

#2

Re: Drying question from a newbie

Allen Neighbors

>I'm not familiar with maple itself, but my suggestion, right off the top of my head, is to cut the pith out of it, and section it into blanks of useful size, and then coat with sealer all over except for the bark. I don't believe the latex paint is a good sealer.

Sometimes when you leave wood in log form, it will check worse than if it is blanked out.

I'm sure someone more knowledgeable than I will chime in here. But that's what is good about this forum... someone will always help you out. :o)

Have a good time turning!!

Allen

Re: Drying question from a newbie

#3

Re: Drying question from a newbie

Bill Howatt

>Allen is right about cutting the pith out of it to reduce the chance of cracking - note that I said reduce not eliminate.

A couple of coats of old latex paint will help reduce the cracking but IMO Anchorseal is much better. With either coating it is a good idea to get the wood roughed down to suitable drying shape ASAP. There is a lot of variation in cracking tendencies. Depends on the type of wood, its history, the environment it's placed in after sealing etc. Fruitwoods like apple crack very easily, maple is probably about average.

If you are making a bowl the general rule is to rough the bowl down to a uniform wall thickness of about 10% the diameter of the bowl. This will let it dry without creating excessive stress and there will be enough wall thickness to allow you to turn the dried bowl back to round since it will be oval when dried.

Spindle turning, where the grain of the wood runs parallel to the bed is less likely to crack but it can happen. Bowl turners typically like turning green while spindle work is usually done dry. This is just a general statement and not everybody works that way.

After you have you green bowl or whatever roughed, put it in a paper bag and stick it in a cool dry place so it can dry slowly. After it is dry, typically a few months, you can then finish it. There are ways of speeding up the drying process like microwaving, kilns,alchohol soaks, liquid-dishwashing soap soaks. I just let them dry in bags often with a handful of the shavings included to slow the process a bit.

While I am rambling, some people coat the roughed bowl in Anchorseal on the end-grain or the whole bowl, or just the inner or outer end-grain. This does slow the drying process and does make cracking even less likely. I only do it if I have some nice piece of wood I really want to reduce the chance of cracking.

The proper way of roughing and drying is a topic that can produce as many theories as there are turners.

Bill

Re: Drying question from a newbie

#4

Re: Drying question from a newbie

Jim Swank

>You've already got some good advice above. Latex paint (two coats is better) will slow down the drying some. Not as good as anchorseaal, but definitely a step in the right direction.

Re: Drying question from a newbie

#5

Re: Drying question from a newbie

john lucas

>Steve What nobody mentioned is, if you turn anything thicker that about 1" out of green wood it will most likely crack when it dries. It takes wood about 1 year per inch to dry although green wood that has been turned and has all sides toward the air will dry sooner. Still it might take months.

Turning thin 3/8" or less is usually a good way to keep things from cracking. I would use green wood just to play and learn the tool techniques but don't try any final projects until you learn more about green wood turning. When I started I glued up dry wood to get the thickness that I wanted. Then you don't have to deal with the cracking problems. If you built the lathe from Woodsmith you already have some woodworking equipment that should help you get dry wood of appropriate sizes to glue up and turn.

Still most turners learn to turn greenwood projects fairly quickly and it sure is nice to make something really great from wood saved from the fire pile. Just keep asking questions and someone will try to answer.

Re: Drying question from a newbie

#6

Leo Van Der Loo

Re: Drying question from a newbie

Leo Van Der Loo

>Hi Steve, how long before you are going to have your lathe ready ?

Latex paint is not a good sealer, latex paint is made for moisture to go thru, unlike oil paint which will blister if moisture wants to get out, I don't know the sizes of your wood, but I would get that wood out of the sun and drying wind if possible, then set it on end, and then pull a plastic bag over the end and wrap a piece of tape or string around it to get the bag tight around the log, now get your lathe as soon as possible, then you can cut the wood into short pieces and take the pith out and rough turn right away, after that let dry in a airstill place, out of the sun and away from the heat, maple rough turned to 8 to 10% wall thickness should be OK here in Ontario, not necessarily so in other places, placing the rough turned bowl in a paper bag for the first few days or a couple of weeks does also help slow down the initial drying speed, do check every few days though, if mildew forms wipe clean and let dry.

Have fun and take care

Leo Van Der Loo

Re: Drying question from a newbie

#7

3/8?

Bill Howatt

>I don't understand turning to 3/8". Although it depends on the diameter of the bowl, I consider 3/8 to be too small to true up an oval bowl after drying. I don't dispute thinner is better for crack reduction but you do have to have a wall left.

Bill

Re: Drying question from a newbie

#8

Steve Kubien

Re: Drying question from a newbie

Steve Kubien

>Thanks for the info everybody. The wood I salvaged was only about 6-8" in diameter. I quartered it and cut the pith out. The bark is still on and I will put another coat or two of latex on today. I guess I will have to get some Anchorseal for next time, based on the over-whelming majority! Much of what I've got will end up being made into pen blanks since that is where much of my interest lies. A couple will make neat bowls or vases.

My gosh, what have I done by going down this turning path?

Steve Kubien

in sunny Ajax, Ontario where it is 21�C and the turkey hang-over is slowly dying off

Re: Drying question from a newbie

#9

Re: 3/8?

Allen Neighbors

>Bill, I think John is referring to turning to finish size while green. I think. :o) Then it will be less likely to crack, but may move some, anyway.

Allen

Re: Drying question from a newbie

#10

Re: Drying question from a newbie

Bill Howatt

>"My gosh, what have I done by going down this turning path?"

What you have done is started down the path to financial ruin but with the newfound knowledge that it isn't the price of the lathe that gets you, it is the cost of the tools and accessories.

All of your other shop tools will now be placed in a subordinate role to do nothing but provide support to lathe.

You will be able to detect the sound of a chainsaw from a distance of 10 miles or 16Km in Canada.

Your neighbours will chain pitbulls to all their prized trees to keep you away.

You will spend hours:

Trying to explain to your wife why the family car needs to be replaced by a pickup truck (for hauling wood).

Convincing her chainsaw oil spilled in the trunk is a good rust-proofer.

Bill

Re: Drying question from a newbie

#11

Steve Kubien

Sounds kinda grim

Steve Kubien

>I REALLY can't see my flatwork tools gathering too much dust. What is appealing about turning is that it won't take a heap of space (compared to the tablesaw, scrollsaw, humunguloid workbench, etc) and I'll actually be able to finish the odd project. Making a few gifts in the form of pens and small hollows holds great appeal as well. As for the chainsaw...SWMBO is actaully getting me one for Christmas!

Thanks everybody,

Steve Kubien