Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Yo! Friendly turner types! RPM knowledge needed.

Posts

Yo! Friendly turner types! RPM knowledge needed.

#1

Yo! Friendly turner types! RPM knowledge needed.

Ron Bauman

>I'm entering the final phases (whew) of rebuilding a PM 90.I've replaced bearings, ordered parts on eBay from all over the lower 48 and some from other bulletin boards. I started with a machine designed to spin metal and wood with a top speed of 4000rpm and a low end of 1000 rpm. This will all be changed. I turn spindles for my stools on a Griz HD and the top speed I use is between 7-800rpm. Its fine for me. My question is this: I want to turn stool seats outboard and dish them and true up the edges. My largest "THE BIG KEESTER" is 16" in dia. I may make larger. The surface speed at the outer edge will be terrific unless I really lower the bottom speed of the lathe. I'm thinking about 200-250 low speed and up to 1000 +- at the top. What say you? Thanks for all input. I won't be able to read anything until the 'morrow, but I appreciate all opinions.

Re: Yo! Friendly turner types! RPM knowledge needed.

#2

2 ways to go.....

TDaniel

>you could put a jackshaft in or you could replace the motor with a variable frequency drive. How much do you want to spend?

Re: Yo! Friendly turner types! RPM knowledge needed.

#3

Re: Yo! Friendly turner types! RPM knowledge neede

john lucas

>Ron I'm someone who turns at lower speeds than many. For me the speeds you are saying are about right. I think you might want a higher speed available just in case you decide to do spindles on it. I turn mot spindles between 500 and 2000.

Re: Yo! Friendly turner types! RPM knowledge needed.

#4

Leo Van Der Loo

Re: Yo! Friendly turner types! RPM knowledge neede *LINK*

Leo Van Der Loo

>Hi Ron

Ron my lathe's top speed is 1500 rpm, as I rarely do any spindle turning that's just fine, but I would like something in the 2000 rpm range if I was to do more spindle work.

Most of my turnings are in the 12" to 20 something range, and I start most of my rough turning at 370 rpm, some smaller and less out of balance I will start at 500 rpm, and seldom go any faster than 1000 rpm, the problem with going slower of course is the cutting close to the center. For starting you seats that are probably fairly round and balanced, starting around 500 rpm should be just fine, so yes if you have several speeds between say 300 rpm and 2000 rpm, you should have it all covered.

Have fun and take care

Leo Van Der Loo


http://homepage.mac.com/l.vanderloo/PhotoAlbum4.html

Re: Yo! Friendly turner types! RPM knowledge needed.

#5

Re: Yo! Friendly turner types! RPM knowledge neede

John Peck

>Go to the following link for an article on lathe speeds by Dale Nish that's available from Craft Supplies USA: http://www.woodturnerscatalog.com/pdf/safe_lathe_speeds.pdf

Re: Yo! Friendly turner types! RPM knowledge needed.

#6

Ron, I have turned a few

Don Henthorn

>fifteen inch dished stool seats on an old Blount lathe with three stepped pulleys and a flat belt. The lowest speed wasn't that slow but I had no problems turning them. I fixed the lathe so I could turn outboard and used a tool rest that was affixed to a four inch pipe welded to an auto tire rim with a section cut away. I bandsawed the blanks and then would mount one on the lathe. I would turn the lathe on and off and cut until the piece slowed down, and then turn the lathe on and off again and resume cutting. As the piece became more balanced I could let a little more time go by between the turning on and off. Didn't take long to get to the point where I didn't have to turn the lathe off. Turning a seat was not a big job.

Here is one batch of the stools.







Here is one of the seats.









Just the way I did it.

Re: Yo! Friendly turner types! RPM knowledge needed.

#7

Brad Vietje

Re: Yo! Friendly turner types! RPM knowledge neede

Brad Vietje

>Your plan is good, Ron. Most lathes are built to go way, way faster than necessary. A top speed of 100 - 1500 if suffucient for almost anything, but lower speeds are real handy for large things, and out-of-balance work. Like TD says, a jack shaft is the easiest and least expensive solution. Remember, a jack shaft can be used to step the speed down or step it up, if the pully sizes are adjusted, so you would still be able to approach ludicrous speed when desired by switching jack shaft pulleys.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Yo! Friendly turner types! RPM knowledge needed.

#8

Re: Yo! Friendly turner types! RPM knowledge neede

Bill Howatt

>If you go the jackshaft route, make sure that you use good hardware with a good mounting system. Poor jackshaft systems can introduce vibration.

Bill

Re: Yo! Friendly turner types! RPM knowledge needed.

#9

Thanks to you all.....

Ron Bauman

>The mulling will begin. I am going to use a series of jack shafts to drop the 1725 rpm of the motor, then the variable speed pulleys of the stock PM90 will do all the work from there. I appreciate everyone's sugestions and will post when the sucker is up and running. Thanks.