Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Powermatic 3520A Tool Rest

Posts

Powermatic 3520A Tool Rest

#1

Powermatic 3520A Tool Rest

Jim Dickman

>The stock tool rest that came with the Powermatic is too soft - knicks easily. I'm looking at the modular tool rest systems out there - 1" straight rods and "S" rods. One manufactire is BestWood Tools.com. Before I buy - any feedback, suggestions, alternatives would be greatly appreciated.

Re: Powermatic 3520A Tool Rest

#2

Re: Powermatic 3520A Tool Rest

Hooligan

>I've used a couple of the modular rests, and they suit the purpose well. A gouge will certainly move across them well.

I am a pretty big proponent, though, of cast iron rests. They just have much better vibration dampening characteristics.

I've not really any complaints per se, of modular rests, I like them but am not really in love with them.

Re: Powermatic 3520A Tool Rest

#3

Re: Powermatic 3520A Tool Rest *LINK*

Sean Troy

>I would highly recommend looking at the Lea tool rests. I'm pretty sure you can have him custom make one just for your needs.


http://www.woodturningtools.net

Re: Powermatic 3520A Tool Rest

#4

Re: Powermatic 3520A Tool Rest

Bob Fawcett

>Jim,

I have a 3520B and both the stock and a modular tool rest. They both nick, especially when using something like a parting tool with sharp corners. The steel in the modular rests is not as hard as your cutting tools (you want it that way).

I like the cast iron because it is easier to dress up. Just a few strokes with a file and its back to use. Draw file the cast iron, it works really well with a good file.

Re: Powermatic 3520A Tool Rest

#5

Leo Van Der Loo

Epoxy some drillrod to your rest

Leo Van Der Loo

>

Re: Powermatic 3520A Tool Rest

#6

Re: Powermatic 3520A Tool Rest

georgetroy

>You could take a look at the Robust or Oneway tool rest. The edge is close to the work and not alway from it like a round one. GT

Re: Powermatic 3520A Tool Rest

#7

Re: Powermatic 3520A Tool Rest

john lucas

>Jim I've been using my powermatic tool rest for about 2 years now. No significant denting. I do have a bestwood tool tool rest and like it a lot. I bought the offset 9" tool rest. It is my favorite rest.

Re: Powermatic 3520A Tool Rest

#8

Re: Powermatic 3520A Tool Rest

John Veerkamp

>I have the best wood tools modular rests on my Delta lathe. I really like them. So far I have the 12" and the 6" straight ones. I'm buying the curved ones soon.

John

Re: Powermatic 3520A Tool Rest

#9

Re: Powermatic 3520A Tool Rest

Duane C.Leach

>I bought a rest from Robust. Basicaly it's a 4" steel pipe cut in 4 ths length ways with a post welded on. Best tool rest I have used.

Happy turning

Duane

Re: Powermatic 3520A Tool Rest

#10

Re: Powermatic 3520A Tool Rest

john lucas

>Duane I don't own one yet but I have been playing with designs for what I think would the best tool rest that I can make with the tools I have. The Robust tool rest seems perfect. Now I'll either have to buy one or build one. I did ask at the AAW show and it does have a 1" tool post.

Re: Powermatic 3520A Tool Rest

#11

Re: Powermatic 3520A Tool Rest

robo hippy

>I have the curved tool rests that Oneway makes, and just love them for my PM (inside and outside bowl rests). However, there is a problem with them now. Oneway made the posts shorter to fit their 16 inch lathe, which makes the post too short for the PM. You may be able to get them to weld a longer post on it, or get the rest and weld your own post on.

robo hippy

Re: Powermatic 3520A Tool Rest

#12

Re: Oneway is aware of PM special needs.

Al Crandall (NE of Indy)

>I bought a curved rest at the Ohio Valley Symposium last year. When I told Kevin that it was for a PM4224, he said he didn't have one with him which was long enough, but that there were some in stock back home. It was mailed to me within a week.

Re: Powermatic 3520A Tool Rest

#13

I did that. Works great.

Don Henthorn

>