Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Making a new friend

Posts

Making a new friend

#1

Making a new friend

Carole Valentine

>I have had a Sorby Multi-tip for about a year but had only used it occasionally and then only with the teardrop scraper. Lately, I have been using it on undercut bowls and have fallen in love with it. I also started using the scraper rolled to a 45 deg angle for finishing cuts and it really works well. I can use it for reverse turning as well to tame wild grain. Do many of you guys and gals have "barely acquainted" tools lying around the shop that you just haven't taken the time to learn to use and really make friends with? I am glad I did with this one.

Re: Making a new friend

#2

Re: Making a new friend

Jennifer@Indy.USA

>Carole, I have a few....Mr. Skew is first on the list :)

Then there's the Sorby version of the Termite tool. I have just never gotten the hang of that thing.

I have gotten to be good friends with my Sorby multi tip too. I love the round scraper for cleaning up the inside of hollows.

Jen

Re: Making a new friend

#3

Re: Making a new friend

Darryl

>Do you sharpen it/them or just hone? I have not had too much luck right out of the box....

Re: Making a new friend

#4

Re: Making a new friend

Bill Stehman

>Hi Carole,

I remember the long conversations when you first tried that tool. Mounting the cutter on the left or right ?? chuckle. They are a good tool and the cutter works mounted either way depending on the application needed. Sorby has since produced a new video even showing a different method for sharpening from the original directions. I use the tools almost daily having two straight and two goose necks so I don't have to change cutters.

I also like the long rs 2000 with armbrace but use the Jamison small Tantung scraper on it for deep hollowing finish cuts. So many ways to skin that cat.. Glad to hear you might start enjoying the tool. They work. Thats my story and I am sticking to it... chuckle.. enjoy.

Re: Making a new friend

#5

Re: Making a new friend

Carole Valentine

>LOL! Bill, Seems to me I had endless questions about every tool I tried when I first started turning! The first one that really stymied me was the Sorby Hollowmaster which is basically just a gooseneck version of the Multi-tip tool. I learned how to use it but it doesn't lend itself very well to the small hollow forms with the small openings that I like to do and I like the straight multi-tip better for open forms. My next quest is a hollowing rig with a laser so get ready for more questions! ;))

Re: Making a new friend

#6

Re: Making a new friend

Carole Valentine

>Darryl, I sharpened scrapers on the grinder the first time with 80 grit. Since then I have only touched them up on the 120 grit wheel. If you'll notice, the multi-tip scrapers (teardrop) are 90 degrees and the Sorby video says to maintain that angle. I don't remember why. I'll check the video again. The other cutting bits I sharpened initially on the grinder. I hit them with a diamond card as I work when the need a tuoch-up. When they really need it (like after I drop the tool on the concrete floor), I put them back on the grinder but not very often. Don't know if any of that is right or wrong, but it works for me.

Re: Making a new friend

#7

Re: Making a new friend

Cyril Griesbach

>I'd sure like to make friends with my multi-tool and the hollowmaster as well. I've always sharpend the cutters as Sorby suggests and I've thought that was my problem. Seems like a few strokes with a diamond hone isn't sufficient. I'm using the Sorby 40mm diamond hone shown in their videos and "tounge oil".

I looked for the new Sorby video on sharpening and didn't find it on their web site.

Any more help would be welcome.

Cyril

Re: Making a new friend

#8

Re: Making a new friend

keith zimmerman, Normal, IL

>I really like my Multi-tip. I have used it a lot to do under-cutting for potourri bowls, and the scraper does wonders on the inside walls. Only drawback is that the opening has to be rather large to get the tool inside the wood.

keithz