Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

I wish I would never have bought a Husqvarna...

Posts

I wish I would never have bought a Husqvarna...

#1

I wish I would never have bought a Husqvarna...

Devon Palmer

>Pardon my Rant.... Just need to vent and get some advice...

I bought a new Husky 357xp from Hoffman Power in Columbus this summer, and have had nothing but problems with it and the dealer. It all started off with my walking my shiney new orange saw to the truck and noticing a "rattle" in the muffler. The service tech "assured" me it was a loose baffle. 3 days later I'm prepping the saw for use, and couldn't stand the through of starting it with that noise, so, I removed the muffler and extracted 1 cap screw: similar to the one that holds the muffler on. Both piston, exhaust port and screw looked in tact so, I thought "ok, these guys are Jerks, they don't get any more of my business".

Fast forward to last weekend. I had used the saw 3 times prior, less than 2 hours of running time, just starting to get broke in and the oiler stopped. I returned it to said dealer to investigate, and they reported that the oiling mechanism was packed with woodchips and charged me $40 for the cleaning. Now, I've had a chainsaw in hand since I was 12 years old cutting wood to heat the family house. I read the manual, adjusted the flow rate, etc. I regularly check to make sure there is oil in the slot and that there are no blocks. Even IF I did miss the clog, is it unreasonable to expect that the dealer would "stand behind" their product, simply clean the slot, and send me on my way? Why have I not had this problem in the previous 30 years with other saws? Given the incident with the cap screw, their credibility is suspect.

I'm wondering what my options are at this point. I'd settle for the refund of my $40, but, am considering legal action to return the saw for a full refund. A hand signed letter to Husqvarna and a Better Business Bureau complaint are most assured....

Devon Palmer, Columbus, Ohio

Re: I wish I would never have bought a Husqvarna...

#2

Ellis Walentine

I feel your pain

Ellis Walentine

>I've got a 346XP and it crapped out on me last weekend when I was cutting wood 20 miles from home. I had to drive all the way home and get my 35-year-old Homelite to finish the job. I took the Husky to the repair shop and they said they were backed up and it would be two weeks before they could look at it. The guy said it would probably need a carbuerator rebuild kit and it would cost about $70. I asked him why the carb would need rebuilding on a saw that is less than two years old and hasn't had more than maybe 50 hours use. He said that if I wanted to spend a couple hours cleaning the carb and air intake manifold with GumOut, I might be able to do it myself. Unfortunately, I think the problem is with one of the fuel lines, and I'll be darned if I want to buy a new carbuerator if the problem is elsewhere.

My idle question is, would I be having a similar problem if it was a Stihl?

Ellis Walentine, Host

Re: I wish I would never have bought a Husqvarna...

#3

Re: I feel your pain

Scott Hogsten

>Yes, I have an 029 boat anchor out in the garage. Bad thing about Stihl is they won't sell you the parts to fix it yourself.

Scott

Re: I wish I would never have bought a Husqvarna...

#4

Re: I feel your pain

Hooligan

>Quite simply Ellis, nope.

I have two Husqy 61's, and they have been good saws for me, but anyone I know that has any of the commercial saws aren't too fond of them. The consensus is that they would rather buy Stihls had they to do it over again.

Re: I wish I would never have bought a Husqvarna...

#5

Re: I feel your pain

Gary in Zirconia, NC

>I just take my Stil in to my dealer and show him the parts I need and he looks them up and sells them to me. No questions.

Re: I wish I would never have bought a Husqvarna...

#6

Re: I feel your gas pain

Mark Mandell - Gone Round In Jersey

>Ellis, I had that problem with my old Stihl when it was fairly new, which was before I got in the habit of not keeping gas stored in my saws. Cost me $150 to have a $350 saw rebuilt with new fuel lines and seals when they rotted out. Since I was fairly PO'd I asked an arborist friend as to the why. Asked me if I used my saw every day. "No." How often? Depends, could be weekly, could sit for 6 months. Told me that 90% of the problem with "homeowned" saws was old gas left in them. "Drain your saw when you're done for the day," he told me, "and your problem will be solved." The old Stihl has run for 13 years since then without a hitch, and my Husky fires after a couple of pulls to prime it. I'll bet your fuel lines have developed a crack or two which breaks the fuel pump's suction so your saw runs out of gas with a full tank.

m

Re: I wish I would never have bought a Husqvarna...

#7

Re: I feel your gas pain

Bob Fawcett

>Stabil in the gasoline helps too.

I use this in the gas can when I mix for 2 cycle. Keeps my string trimmer and Craftsman saw running, even though I use the saw infrequently. Wish I had put it in the old Harley when I had to store it while the

Re: I wish I would never have bought a Husqvarna...

#8

Ellis Walentine

That sounds like exactly it, Mark

Ellis Walentine

>In fact, I pointed out to the guy that there was some fuel around the handle and the saw smelled of gas. What irked me is that he didn't mention replacing the fuel lines -- he seemed fixated on rebuilding the carb. I think the carb only needs a little washing out with gum our or clean gas.

Phooey. I'm going to go back there and see if I can buy a set of fuel lines and then do the whole thing myself.

Thanks,

Ellis

Re: I wish I would never have bought a Husqvarna...

#9

Re: I feel your gas pain

Bob Fawcett

>house was under construction. Was supposed to take 6 months - turned into 2 years.

Re: I wish I would never have bought a Husqvarna...

#10

Brad Vietje

Are Urban Dealers the Problem ?

Brad Vietje

>Just a passing thought... Could it be that dealers in urban or highly-populated suburban areas are part of the problem ? They have a large population base to draw upon, and maybe they don't care as much if you don't come back because many others will. I also suspect there is a much greater expectation in rural areas that chainsaw buyers have either used saws before, or at least had a lot of exposure to them than in cities, where fewer people are apt to own or use one. Maybe they are less likely to try to "pull one over" on a customer.

I live in a very rural area, and dealers around here can not survive treating customers like that, because they need your repeat business. We have to drive a bit further to get to them, but generally dealers in the boonies seem to treat their customers better. I also feel that a dealer should be paid for services rendered, but a simple oil port cleaning can only take a few minutes, and on a saw that was just purchased, I'd clean it for free and show the customer how to look out for that in the future if I were the dealer. Establishing a good relationship with a customer is much better than just charging book rate for each and every little adjustment or tweak -- they sure didn't win you over !

In short, you can be nearly anonymous in a medium to large city; no chance of it around here.

Safe spinning,

Brad Vietje

Newbury (in the boonies of northeastern) Vermont

Re: I wish I would never have bought a Husqvarna...

#11

Re: I feel your gas pain

Mark Mandell - Gone Round In Jersey

>Bob,

I use stabilizer as well, but that only keeps the gas from going bad. It will still rot the lines and seals if left in the saw.

Re: I wish I would never have bought a Husqvarna...

#12

Re: I feel your gas pain

Bob Fawcett

>You are correct.

It will prevent some of the gumming up of a carb.

Re: I wish I would never have bought a Husqvarna...

#13

I think you hit the nail on the head....

Devon Palmer

>Brad,

You make an excellent point. I come from a small farm town in North Eastern Indiana. You always strived to "make it right" by your neighbor, and go the extra mile to maintain those relationships becuase you needed each other. It would explain why we're seeing such things as "Angies list" and other referral services.

I must be spoiled by the FANTASTIC service I get from our local Woodcraft store, and other locally owned family businesses.

- Devo

Re: I wish I would never have bought a Husqvarna...

#14

Stihl Parts

Dave Lambert

>Hey Scott,

There are a number of places on the internet where you can order Stihl parts. I have used Peralta Power Equipment out of New Mexico in the past and had good results. The draw back is that you have know exactly what you want and you need the parts manual (different than the repair manual) in order to get the proper part number. I was able to replace the piston and cylinder for my 066 this way. It was a bit of a pain, but I did save alot of money.

Hope this helps.

Re: I wish I would never have bought a Husqvarna...

#15

Keith Tompkins

Re: I feel your pain

Keith Tompkins

>Hey Ellis, Most chainsaw carbs have an internal screen to keep debris out of the jets. Simple to get to: remove the carb, blow out the screen, reassemble. A partially plugged screen raises havoc on the running of the saw. Replace any fuel lines while apart. Piece of cake. Most chain saw oil contains additives which help keep gasoline in good condition over the winter.

Re: I wish I would never have bought a Husqvarna...

#16

Brad, that is it.

TDaniel

>When I take my chainsaw in for service it normally costs me $15. I have both Huskies and Stihls and a Jonsered and I consider all of them equal. When I have had a major problem Stihl has been the best company to get things straightened out, even to the point of pulling their line from one shop who refused to fix a problem he created. I definitely agree that rural shops give better service. I never buy a chainsaw from any source that does not service them. Don't even buy a chainsaw from Home Depot or Lowe's.

Re: I wish I would never have bought a Husqvarna...

#17

Re: That sounds like exactly it, Mark

Ken Oakley- Sunny St. Cloud, Fla.

>I have had the same problem with a Honda lawn mower and a Honda pressure washer and years back with a Murray lawn mower. Now I use a stabilizer in the gas and if I think it will be sometime before I use the equipment again I either empty the tank or run the tank dry.

Re: I wish I would never have bought a Husqvarna...

#18

Re: I feel your pain

Mac

>Yesterday I bought a new Husky from the same dealer that I purchased one from 9 years ago.My local dealer,here in the boonies(by city standards)has taken excellent care of anything I have purchased from him.Couldnt ask for better service. I am a bit rough on saws and he has always been great.The dealer is the most important part of any tool purchase.Find someone who has been and will be in business for the long run and you both win.

Re: I wish I would never have bought a Husqvarna...

#19

Tree Service

W.C. Turner

>I've got a friend in the tree business, that used to always use Stil's, but, switched to Husky, and told me they like the Husky's a lot better.

W.C.

Re: I wish I would never have bought a Husqvarna...

#20

Ellis Walentine

Yeah, maybe I should repair it myself

Ellis Walentine

>I don't know when I will have the time though. And, I wonder what they'll charge me for new fuel lines? I wish I felt comfortable with this dealer. My other small engine guy went out of business a couple years ago and I'm on my own with stuff like this.

Cheers, and thanks,

Ellis