Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Chainsaw Chain Problems

Posts

Chainsaw Chain Problems

#1

Chainsaw Chain Problems

Devon Palmer

>All,

Been playing with my new Husky 357XP ripping up 2.5 ton (4 skids) of logs for bowl blanks, etc. I've been having nothing but problems with the new saw. Its actually performing worse than my little 42cc Poulan in certain situations. (it sounds GREAT tho, like a little Harley )

Its VERY bad at clearing the woodchips when ripping: even if I pull the saw back several inches from the wood. I'm still using the chain that came with it - safety chain with these HUGE rounded-over bumpers.... I'm wondering if these could be part of the problem. I think they might be grabbing the longer woodshavings and dragging them through the saw as opposed to letting them eject out the bottom. The little saw doesn't have these and doesn't have the problem.

Has anyone experienced this? I'm definately replacing the chain w/ one without the anti-kickback as I'm faily experienced and wear the appropriate safety gear and equipment like chainsaw chaps, secured sawbuck, etc... What chain does everyone else use? This saw spends 80% of its time Ripping, and I use the other lighter saw to shape. Should I get a ripping chain?

Sincerely,

Chainsawless in Columbus

Re: Chainsaw Chain Problems

#2

Re: Chainsaw Chain Problems

Keith Newton

>I am not familiar with that saw, but I'll bet that chain is contributing to the problem.

If you are cutting with the chain running straight down the grain. This will as I am sure you already know create the longest chips. If you will lead a bit more with the bar-tip, so the blade is cutting a bit more against the grain, they should break up, and clear a little better.

Re: Chainsaw Chain Problems

#3

Roger Dunn

Re: Chainsaw Chain Problems

Roger Dunn

>Devon,

I think you should try a chisel tooth square ground semi or full skip chain configuration. I use them for doing a lot of ripping for wet big leaf maple. They do a good job of clearing out the kerf and you don't have to go to the more expensive ripping chain. The terminology and Oregon chain order numbers are on Madsen's website page found here:http://www.madsens1.com/oregon3.htm. Their website has a lot of useful info on chains and saws. They are good people to deal with, I don't have any affiliation, just a satisfied customer.

Good luck

Roger

Re: Chainsaw Chain Problems

#4

Re: Chainsaw Chain Problems

robo hippy

>If by ripping you mean cutting parallel to the grain, then the long shavings tend to build up faster than the saw can clear them. The wetter the wood is, the bigger this problem is. You can try cutting at a 30 degree angle through the log (which makes shorter shavings) rather than parallel to it. A skip tooth blade helps. Also I have found that when they are clearing well, as you get lower in the log, if they pile up under the chute, it will plug up, but then they come around and off the top of the blade. If the shavings are totally clogging up the saw and bogging it down, Then I don't really know what is going on.

robo hippy

Re: Chainsaw Chain Problems

#5

Re: Chainsaw Chain Problems

Hooligan

>A skip tooth isn't going to do you a lot of good, as far as clearing is concerned. The main problem with ANY Husqy saw is that there is a low angle of clearance for chip ejection. I have seen a couple of modifications for them, but have yet to do it with mine. The only saw that I rip with is my 088, and on that I run a 42" sqauare skip. I haven't used my Husqy saws for ripping, for the very same reason. I was told just not to bother with it, and I haven't.

Re: Chainsaw Chain Problems

#6

Re: Chainsaw Chain Problems

DaveZ

>I agree about using a chisel chain, but I disagree with using square as opposed to round. The reason is that the square is much more difficult to maintain, i.e. files are about $5 per and the learning curve is large. Square will cut faster than round when crossgrain cutting, I don't know about sidegrain never tried it. Anyway, while square is faster cutting, that is only initially, it also gets dull faster, which brings us back to the maintenance issue.

Re: Chainsaw Chain Problems

#7

Re: Chainsaw Chain Problems

DaveZ

>Devon, I think changing your chain will help some. I have a 359, which is pretty close to being the same saw. Part of the problem,imo, is that since the saw has an outboard clutch, it tends to clog quicker. On my 372XP, which has an inboard clutch there is much less of a clogging problem. You can modify the bar cover to give more space for chip removal, however I decided to just clean it out more often and leave it stock.

No need for ripping chain unless you have the saw set up as a chainsaw mill.

Re: Chainsaw Chain Problems

#8

Re: Chainsaw Chain Problems

Mark Mandell - Gone Round In Jersey

>Devon,

I rip-cut with my Husky (372XP) all the time with no hassel at all. I'm pulling a 28" bar with a full-skip chain. I do, however, cut at a 15 to 20 degree angle to the line of the pith so that my chain is cutting somewhat across the annular rings. This serves to shorten the ribbon shavings making them easier for the saw to clear, and also gives better control of the cut. Since you mentioned a saw buck, I'm assuming that you're cutting clear of the ground so that the bottom of your saw's chip chute is not obstructed. Your depth gauge-links should not be the problem because without them the ribbons would be much thicker and even harder to eject, plus you'd put much more stress on your motor and drive system.

Just a note on chain types. Many people regard "skip tooth" chain as "ripping" chain, while others refer to ripping chain as the Granberg type which is designed to be used only in Alaska mills for ripping planks. Granberg chain is very dangerous because its configuration creates very high kickback forces beyond the usual upper nose-catch. Grandberg, its inventor, states flatly that such chain is NEVER to be used in hand-held saws.

Re: Chainsaw Chain Problems

#9

Re: Chainsaw Chain Problems

Peter Teubel

>One modification I made to my Stihl (inboard clutch style) was to remove the chain-catcher...a little metal tab right under the exit path of the chips/shavings. No problems ripping with the grain at 0 degrees. Nice long shavings exit quite nicely PROVIDED one keeps the chain speed up, let the saw's weight be the only down force, and clearing away the pile of shavings under the saw frequently.

Re: Chainsaw Chain Problems

#10

Re: Chainsaw Chain Problems

Hooligan

>You are correct there Mark. The Granberg style chains that have the top plate removed aren't to be used in a saw that isn't in a mill.

Oregon RD chain, is a different style rip chian that is a lot less prone to the force kickback is a good rip chain. It has the top plates left on, and a couple other differences. It's ground at a 5 degree bevel, I believe, and at 25 or 30 degree tooth angel.

The other thing to keep in mind, is that with true rip chains, the intent is that you are cutting end grain, NOT for cutting axially....

Just something to think about.

Re: Chainsaw Chain Problems

#11

Re: Chainsaw Chain Problems *LINK*

Rick Allen

>Have you considered contacting Husqvarna about the issue to see if they have any recomendations.


Ask Husqvarna

Re: Chainsaw Chain Problems

#12

Re: 5* Bevel??

Mark Mandell - Gone Round In Jersey

>I grind my own chains, but use a 62* set on the bevel (28* off vertical) and 27* on the tooth axis. Gives me better edge/point durability cutting hardwood. I've never seen a chain ground at only a 5* bevel. That would seem to be putting a whole lot of strain on both chain links and saw to keep such a blunt tooth edge cutting.

m

Re: Chainsaw Chain Problems

#13

Re: 5* Bevel??

Hooligan

>All of my Oregon RD chains are ground to 5 degrees, thats what they come to me at from the place I get them. I had a hard time finding what I wanted, but Madsens in Washington state had them, were able to provide the answers that I was looking for, and have proceeded to have great service.

I'll be the first to admit that I don't know everything when it comes to the particulars of it, butfor running in a mill, it works great.

Re: Chainsaw Chain Problems

#14

You've ID'ed problem

Jack Riley

>I have two Huskys;a 51 & 55 and experienced the same problem when the 55 was new ie. rounded rake vs. straight. I replaced the blade and the problem ceased. Just give the port enough room for the chips to exit. Don't get too close to the ground and don't let the claw rest against the log when ripping.

Re: Chainsaw Chain Problems

#15

Gotcha

Mark Mandell - Gone Round In Jersey

>"Mill" chain only. Granberg is also ground with the cleaners at a low angle. I thought you were talking about "free-hand" chain.

m

Re: Chainsaw Chain Problems

#16

Re: Gotcha

Hooligan

>My fault if I didn't make that clear. Sorry.

Re: Chainsaw Chain Problems

#17

Re: Chainsaw Chain Problems

Devon Palmer

>Roger,

Thanks for the link. I checked out Madsens site and was there for well over an hour reading and learning Chainsaw chain design, construction, operation and terminology. I'm going to give them a call and order two chains this morning.

Thanks again,

- Devo

Re: Chainsaw Chain Problems

#18

Roger Dunn

No worries! I'm glad Madsen's could help.

Roger Dunn

>