Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

The beginner needs advice *LINK*

Posts

The beginner needs advice *LINK*

#1

Barb Siddiqui

The beginner needs advice *LINK*

Barb Siddiqui

>I did a search on 'jamb chucks' and only found recommendations on woods to use.

Today I turned a pine jam chuck to fit inside a finished little 'nut bowl' of birch.

I'd waxed it on top of shellac, nestled it in against the jam with a paper towel to

protect the finish, and brought up the tail center stub (I have no cone yet.) The

little bowl kept slipping round the jamb chuck, and though I finished and parted

it off, it was difficult to handle. Suggestions?


Woodworker's Essential Facts, Formulas & Shortcuts

Re: The beginner needs advice *LINK*

#2

Barb Siddiqui

oops...forget the link.

Barb Siddiqui

>

Re: The beginner needs advice *LINK*

#3

Re: The beginner needs advice

Barbara Gill, Remlik VA

>I have only used a jamb chuck a few times but when I did I used an old rug pad for protection and friction. Be sure that it will not rub off just in case the bowl does slop a little. I have heard of using a piece of router pad also.

Re: The beginner needs advice *LINK*

#4

Masking tape around the rim - helps hold it on too

Devon Palmer

>

Re: The beginner needs advice *LINK*

#5

Re: The beginner needs advice *LINK*

john lucas

>Barb You need something with more friction. I have uses 220 grit sandpaper, leather, and rubber sink stoppers. I now use the rubber sink stopper the most. I usually don't worry about the inside finish until after I'm done. It's too easy to stall the wood with a heavy cut and this spins the bowl on the jam chuck. That can damage the finish inside. Check out the link below for other methods of reverse turning.


http://www.cumberlandwoodturners.com/tips.asp

Re: The beginner needs advice *LINK*

#6

Router mat or waffle shelf liner

Carole Valentine

>Barb, either will provide enough friction. Most any jam chuck will take only light cuts, so go easy. Another thing you can do is turn a wood taper (use hard maple or something similar) to fit your tailstock and put a little pad of the same material on it to contact the base of the piece.

Re: The beginner needs advice *LINK*

#7

Try a few pieces of double sided tape inside

Wayne Allen - Carson City. Nevada

>

Re: The beginner needs advice *LINK*

#8

Re: The beginner needs advice

Bill Hale / Woodspinner

>I use them on a regular bassis. If the bowl is large enough I use a kitchen hot pad.

When I insert the chuck I make sure the end of the chuck matches the size of the botton and not on the sides. I use a fairly high pressure, turn at high speed and take ligh cuts. On a 12 in. bowl I will leave only a 1/4 to 3/8 tip center nub, sand to about 220 and remove from the lathe for tip removal.

Good turning and be safe

Bill in Casa Grande, AZ.

Re: The beginner needs advice *LINK*

#9

Barb Siddiqui

Good suggestions, thanks

Barb Siddiqui

>I need to make one of those 'donut' holders, but in the meantime, I'll try some of these. It was a little 4" shallow dish, so a piece of router matting may do the trick. I need to turn a hardwood cone shape for the tailstock, too. Thanks.

Re: The beginner needs advice *LINK*

#10

Re: Router matting

Russ Fairfield

>Beware of used router matting. It will have a lot of imbedded dust and grit that can leave an image on the finish. New can do the same thing. but not as bad as used.

Re: The beginner needs advice *LINK*

#11

Re: I'm a beginner too, and I use

Allen Neighbors

>Foamies. These are 1/8" thick sheets of foam that are sold in the craft area of Wal-Mart. You can get all colors of it, and I use white or black, depending on the wood I'm turning. They're about 40-50 cents a sheet for the type with adhesive on it. I stick the adhesive side to the jam-chuck.

I learned this from John Lucas, I believe. Thanks, John!

Hope this helps.

Allen

Re: The beginner needs advice *LINK*

#12

Barb Siddiqui

Thanks Russ

Barb Siddiqui

>I had too much to 'retain' after being at your place. Didn't you show me a jamb chuck lined with leather, and stapled way back around the back? Were those huge staples, or did you wrap heavy wire and pound it in somehow? I made mine out of pine thinking it would be better in softwood, but now think the woodworm screw is going to destroy it soon, so hardwood may be better. People use MDF though. I'll make a donut holder, but this little, straight-sided dish/bowl may not have worked well in that anyway. It's similar to the padauk bowl, but with straighter sides. I sure like the Sorby multi-scraper you advised me to buy.

Re: The beginner needs advice *LINK*

#13

Barb Siddiqui

Thanks, Alan; sounds good.

Barb Siddiqui

>

Re: The beginner needs advice *LINK*

#14

Leo Van Der Loo

Depending on the shape, this way can also. 

Leo Van Der Loo

>


img

Re: The beginner needs advice *LINK*

#15

Barb Siddiqui

Thanks, Leo

Barb Siddiqui

>