Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Grinding safety?

Posts

Grinding safety?

#1

Grinding safety?

Leppikallio

>I'm sure this question is trivial and probably stupid as well. But my wife asked it and I didn't know what to answer so... Why I'm not scared while sharpening lathe tools in my workshop? This refers to those sparks and all that dust and shavings. And I don't even have that grinder right behind me...

So, do you feel comfortable while sharpening tools in your shop? This would be perfect situation to order the Tormek but I'm not quite convinced...

Re: Grinding safety?

#2

If you grind normally.....

TDaniel

>there is no problem with the sparks. However, if you grind heavily, throwing lots of big sparks or if you connect a shop-vac to the grinder I would be more cautious. It wouldn't hurt to keep the area around the grinder a bit clean either. No big alarms here but a little caution can't hurt. And, of course, always have a working fire extinquisher handy just in case..... :)

Re: Grinding safety?

#3

Re: Grinding safety?

Tony Reynolds somewhere near Newark, Ohio

>I have the grinder right to the left of my turning position so it's quick to sharpen and go. I do try and keep the dust and shavings cleared away for the reason stated, and have never had a problem until the other day when I'd left a steel wool pad on the grinder stand. I was doing a quick touch up on my gouge and smelled something burning. The sparks had lit up the steel wool. That was exciting with a 3 foot deep pile of shavings near by on the floor. That won't happen again. Back to roughing out.

Tony

Re: Grinding safety?

#4

Re: Grinding safety?

Hooligan

>I pre-ordered the Jet sharpening station. Less money than the Tormek, and built better. For the primary reason you stated. My shop is getting MUCH smaller, and it just made sense to do so. Although, the grinder will still be used in a considerable fashion, I am sure.

Re: Grinding safety?

#5

New WWers should know

Bill Howatt

>that steel wool can catch fire and it has to be treated with considerable care. IMO, it is not something that is obvious.

Another thing is not to use the same grinding wheels for ferrous metal and aluminum. This can create thermite with disasterous results; I believe this was described in a Lee Valley monthly catalog a few years ago. Just how high the probablility of creating a reaction is, I don't know.

Bill

Re: Grinding safety?

#6

Re: New WWers should know

john lucas

>Bill I'll have to read up on that. For many years I only had one grinder. I have ground I don't know how much aluminum and steel on the same grinder. Never a problem other than clogged wheels that need to be cleaned frequently.

Re: Grinding safety?

#7

Keith Tompkins

Re: Grinding safety?

Keith Tompkins

>I would consider wearing a mask while grinding, as considerable abrasive and metal dust is created while sharpening. Even worse, when trueing up the grinding wheels, much larger quantities of dust are created.

Re: Grinding safety?

#8

Re: New WWers should know *LINK*

Bill Howatt

>John,

Here's one. I did find another one but it looked like the same story but with a British Columbia craftsman rather than an Esso employee. IIRC, this may have been the one in the Lee Valley catalog. From what I see, setting the mix off isn't that simple unless you are unlucky.

Bill


Grinding accident

Re: Grinding safety?

#9

Re: New WWers should know

john lucas

>Fascinating. Definitely don't want to lose half my mustache.

Re: Grinding safety?

#10

Re: Grinding safety?

Bob Fawcett

>Someone posted pictures a few weeks ago of a grinding station with a small shop vac built into the base and connected to the grinder. This should collect the majority of the dust. It also looks safer since the vac was dedicated to the grinder station and should not collect flamables.

Re: Grinding safety?

#11

Probably ok if...

TDaniel

>it is a dedicated shop-vac. If there is wood-dust mixed in then it becomes a fire hazard as a spark would be fanned as it hits the wood-dust and could ignite.

Re: Grinding safety?

#12

Re: Probably ok if...

Merv in BC

>Wood dust and sparks in an enclosed space such as a vacuum system WILL be an explosion hazard even if it is dedicated to the grinder only it will still draw in fine wood dust. Be Carefull