Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

First hollow vessel

Posts

First hollow vessel

#1

First hollow vessel

keith zimmerman, Normal IL

>I have completed my first hollow vessel. It is made from Spalted Maple. It is approximately 5 1/2" in diameter and 3 1/2" high. the finish is Minwas Tung Oil Finish.

This vessel was turned using my 1/2" new Kelton hollowers mounted in a Don Pencil armbrace. I really like using the armbrace. It made it real easy to keep the hollowing tips at the proper presentation. I had no catches on this piece at all. I surprised myself.

I wound up using Carole's suggestion and turned a jamb chuck to fit the opening. It seemed to work quite well while finishing the bottom.

Thanks for looking.

keithz

Re: First hollow vessel

#2

I suppose I should attach the photo... 

keith zimmerman, Normal IL

>


img

Re: First hollow vessel

#3

JL

Re: Nice grain pattern and swirl - real pretty

JL

>

Re: First hollow vessel

#4

Re: I suppose I should attach the photo...

Norm Smith in Nova Scotia

>Hey Keith,

That looks great. Nice job. I have had the same hollowing tools for a few years and love them.

Norm

Re: First hollow vessel

#5

My crystal ball shows more .....

Jamie Donaldson

>....additions to Keith's hollowing tool collection in the near future! You can't get by with just one or two, and I believe there are more versions of hollowing tools, many of them redundant or nearly useless, than any other turning style.

Re: First hollow vessel

#6

Re: I suppose I should attach the photo...

Carole Valentine

>Good job, Keith. I have the DP armbrace but I don't use it. Never got comfortable with it. I feel like if I did get a bad catch, an armbrace could really cause some injury. I use my Keltons in either a Kelton or Hosaluk handle.

Re: First hollow vessel

#7

Re: I suppose I should attach the photo...

keith zimmerman, Normal, IL

>Carole, the DP armbrace fits my arm really well. I found that I can control the torque much easier using it to hold the tools rather than the straight handle. I use the Kelton handle with my mini set and have occasionally had torque issues with it. I think the DP armbrace is too large for the mini set though.

keithz

Re: First hollow vessel

#8

Re: My crystal ball shows more .....

keith zimmerman, Normal, IL

>Jamie, the Keltons I used are not my first hollowing tools, they are additions to my "collection". I currently have the mini and 1/2" sets of Kelton Hollowers, a Don Pencil Scorpion w/ armbrace, a mini and 1/2" Sorby swanneck hollowing tool, a Sorby multi-tip hollowing tool, and a Henry Taylor 80degree hollowing tool.

Who knows if I will acquire any more. I plan to use the Keltons for a while and get used to using them.

keithz

Re: First hollow vessel

#9

Brad Vietje

Excellent !

Brad Vietje

>Great Job, Keith ! Is this your first hollow form ever, or your first with the new tools ? This is a pretty tough profile to start off with, because there's a lot of under-cutting. Can't wait to see more...

Safe spinning,

Brad Vietje

Newbury, VT

Re: First hollow vessel

#10

Re: Nice grain pattern and swirl - real pretty

Norm Smith in Nova Scotia

>I use my armbrace at least a few times a week and have never had an injury or problem with it. For heavier stuff I use the Jamison setup, than tidy up with the arm brace.

Norm

Re: First hollow vessel

#11

Re: Excellent !

keith zimmerman, Normal, IL

>Brad, thank you for your kind words.

This is my first hollow vessel in which I did the turning through a 1 1/2" opening, not my first experience at undercutting. I have made quite a few potpourri bowls where I undercut the lip of the bowl, but they had 3" openings so I only had to undercut about an inch. I have never gone so deep with the undercutting.

This vessel is also the first where I tried to create something close to what I perceive as a traditional vessel form.

I have used the mini-Keltons before, but not the 1/2" size and I have never used an armbrace.

I think the main reason I made this was to see if I could. I'm sure there will be more to come.

keithz

Re: First hollow vessel

#12

Re: Nice grain pattern and swirl - real pretty *LINK*

Darrell

>Nice wood, nice form and well executed. Potpouri bowls are great practice for the undercut and it has obviously paid off here. I have used my home made arm braces quite a bit for the last few years, sometimes on large pieces, and no problems even with a catch or two (or...). The cutters we use are so small that the catches are not so bad. At least for the arm. Why do they happen when the wall is thin?


Around the Woods