Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Cleaning a chainsaw?

Posts

Cleaning a chainsaw?

#1

Cleaning a chainsaw?

Carole Valentine

>How do you guys and gals go about cleaning up your chainsaws when you have been cutting really green, sticky wood? Mine cut a lot of green walnut today and it is a mess. Taking it apart and wiping it down and brushing it out (which is what I usually do) is just not getting it this time. Was going to try a friends compressor, but I don't know if it would have any effect and I'm afraid of blowing junk in the little oil hole.

Re: Cleaning a chainsaw?

#2

Re: Cleaning a chainsaw?

Allen Neighbors

>Carole, I'd take it to the car wash, if necessary, and just make sure you don't force water into the oil hole. But most of the time, you can take the bar and chain off, and brush and use air at the same time. If you think you have blone chips or dirt into the oil hole, a little air in the tank will push it out with oil.

Clean the aircleaner in a little gasoline, and then dry, and spray and work in a little WD-40. (Some manufacturers recommend washing in warm soapy water.)

If your saw is still sappy and sticky after the best you can do, wipe it down with a rag soaked in mineral spirits. (Lacquer thinner or Acetone will damage plastic parts.)

Hope this helps.

Allen

Re: Cleaning a chainsaw?

#3

Dick Hines

Re: Cleaning a chainsaw?

Dick Hines

>Clean a chain saw? Really? All I do is clean the chips out of the chip shoot and lossen the chain. Depending on what I was cutting I may, usely may not, sharpen the chain.

Re: Cleaning a chainsaw?

#4

Re: Cleaning a chainsaw?

Russell L. Babbitt Jr.

>I don't know about that little oil hole but I'll remove the bar cover, bar and chain and will use Simple Green or other degreaser and scrub with a stiff brush. I do use an air compressor and blow out the gunk in those tight spaces. I do this after most major jobs and replace the chain with my sharp spare. The worn chain goes to the shop for sharpening for the next time.

Re: Cleaning a chainsaw?

#5

Re: Cleaning a chainsaw?

Brian Hahn in SW Wisconsin

>Personally, I don't worry about what the outside of the chainsaw looks like afterwards. Whatever is on will be dry and get worn off the next time I use it, only to be replaced with a different layer of crud. However I have been known to clean my chainsaws every couple of years with compressed air. I don't worry about the oil feed hole because the oiler is strong enough to force any minor debris out through the chain bar. If the handles are really sticky, I'd clean them with a cleaner like Simple Green or mineral spirits, depending on the source of the crud.

The most important thing for me is making sure that the chain is sharp and that the engine exhaust port spark arrestor screen isn't clogged.

Re: Cleaning a chainsaw?

#6

p.s.

Brian Hahn in SW Wisconsin

>I usually put the chainsaw on top of a shallow pan filled with saw dust or wood chips to soak up the oil that inevitably leaks out. The pans I use are disposable aluminum muffin pans and disposable pie plates. They are customized (i.e. slightly mangled) by the weight of the chainsaw so they fit "perfectly".

Re: Cleaning a chainsaw?

#7

Re: Cleaning a chainsaw?

john lucas

>Carole other than cleaning out the air breathing ports, pulling the cover off the chain guard and cleaning that out and occasionally wiping down the air filter, I haven't done a thing to my chainsaw in at least 4 years.

Re: Cleaning a chainsaw?

#8

Re: Cleaning a chainsaw?

adrien

>Allen, I misread your typo for "blown chips" as "bone chips" and was horrified at the concept

Re: Cleaning a chainsaw?

#9

Re: Cleaning a chainsaw?

Dale Stansbery

>On the rare occasion that mine gets so unbearably gunky with chain oil, saw dust and dirt, I take the bar off, scrape the worst gunk off, then use a parts washer with mineral spirits to flush the rest away. If its really bad, I'll flush the whole external engine off, then let it dry well before re assembling.

Re: Cleaning a chainsaw?

#10

RE: Cleaning Chainsaws

DaveAnderson (Pac NW)

>Carole,

For 8 years, I made my living repairing chainsaws. First as a service manager for a McCoulough distrubutor in the Intermoutian west, The as the head mechanic for a Logging Supply in the PacNW. When we would get a saw in that was thick with sap. The best remedy was 1 cup of Tide detergetent in 1 gallon of hot water (USE GLOVES1 it will burn skin if left on) then scrub with a medium bristle brush.. The sap will melt like magic. Aquick rinse with clean water and your done. The sap is alkaline senitive and solvet resistant. Just keep it out of the carbuetor and you will have no problems.

Dave Anderson

(PacNW)

Re: Cleaning a chainsaw?

#11

Re: Adrien, I just realized

Allen Neighbors

>that I mispelled blown. Blone. Where the heck did that come from?

Bone chips would be a scary thing, wouldn't they? :o)

Allen

Re: Cleaning a chainsaw?

#12

Re: RE: Cleaning Chainsaws

Carole Valentine

>Thanks, all for the responses. A friend told me to spray gunk remover on it let it sit for a bit, scrub it down then hose it off with the garden hose. Garden hose??? I thought he was nuts wanting me to spray my beloved Stihl with WATER! It seems to me that water would rust everything that's not plastic ??? Should you run the saw afterwards to dry it out? I know you guys are probably rolling your eyes, but I like my lathe, my bandsaw and my chainsaw clean when I finish up a project. LOL Now if I could only transfer some of that obsession to the shop and the house....

Re: Cleaning a chainsaw?

#13

Dick Hines

Re: RE: Cleaning Chainsaws

Dick Hines

>A clean chain saw is the sign of a sick mine.

Re: Cleaning a chainsaw?

#14

Re: Cleaning Chainsaws

Brian Hahn in SW Wisconsin

>Gas chainsaws aren't part particularly bothered by moisture unless it gets into the carburator. The internal metal parts are usually aluminum for heat dissipation, so rust isn't an issue. The drive sprocket, chain and bar are steel, but a little rust won't hurt them and will quickly disappear the next time you use the saw. On the other hand, leaving the saw sitting in a tub of salt water would be a definite No-No.

Just imagine the headline: "Logger Refuses to Work In the Rain Because His Saw Will Get Wet"

Re: Cleaning a chainsaw?

#15

Re: Cleaning Chainsaws

Wilford Bickel

>When we bought our farm about 16 years ago there was a large (26" diameter +) sweetgum tree growing on the water side of the dam on the pond that was causing the dam to start leaking. I was cutting it down with my big McCulloch one morning with one leg in the water when I realized I was slipping on into the pond and that things were not going well!! I hit the off switch on the saw and it and I went swimming!!!! Took the saw and put it on top of the dam in the summer sun, opened it all up and flushed the carb and cylinder with gas mix - Let is sit in the sun all afternoon. Late that evening it cranked on the second pull - finished cutting the tree down and it is still running today!! A little water won't hurt it as long as it is kept out of the carb and cylinder! I usually blow mine out with the air compressor when I get through using them before they get put up.