Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Grinder location

Posts

Grinder location

#1

Grinder location

john lucas

>I spent all day yesterday rearanging my shop. Boy was I tired. I desperately needed more room for building large flat wood projects. (Don't tell anyone I do these) I'm having a very hard time finding a place for the lathe tool grinder. Between the length of the wolverine jig and the large area needed to swing a bowl gouge, it takes up a lot of room. I have my lathe tools and stuff in a moveable cabinet so I can push it out of the way when building cabinets and such. I may end up doing that with the grinder. Where do you put your grinder?

Re: Grinder location

#2

Re: Grinder location

Carole Valentine

>On a bench against the wall immediately behind me when I am at the lathe. Very convenient. Turn, step, grind - turn, step, start turning again.

Re: Grinder location

#3

Brian McKearney

Re: Grinder location

Brian McKearney

>I have mine mounted to a moveable cart, as shown in the pic. Don't mind the mess!!! I got the idea for this cart from Wood Magazine a few years back - the great thing about it is that the cart serves double duty - the top rotates on a steel rod (something like 3/8", I think) and I have my grinder mounted on one side and my scroll saw on the other. You might have noticed that I have two carts - the other holds my 6-48 bench sander and planer. There is some space for small stuff on the shelf underneath, but that area needs to be kept pretty well clear so that you can rotate the top to switch tools.

Hope this sparks some ideas!

Brian


img

Re: Grinder location

#4

Re: Grinder location

Ron in Drums PA

>Carole, you forgot the important part

Turn, step, grind - turn, step, turn... Cha, cha, cha

Re: Grinder location

#5

Re: Grinder location

Bob Fawcett

>I built a similar cart from plans in ShopNotes. I use it for my 6 x 48 sander and planer just as above.

My grinder is on a pedestal made from an old car tire rim and a section of black iron pipe. (I used to be a mechanic). The footprint of the base is no larger than the grinder. It is also a very convenient height for standing, several inches taller than it would be on a bench. I mounted the grinder on a section of 8/4 Oak I had. This thickness allowed me to route a groove for my homemade wolverine type arm. (a section of "T" track inverted with an allen head machine bolt pocket). The only bad part is it is in another room in the basement and I have to walk 20' to the grinder.

Re: Grinder location

#6

Re: Grinder location

n2wood

>Nice lathe Brian

Re: Grinder location

#7

now you got me started.

john lucas

>You put your bowl gouge in, you put your bowl gouge out, your put your bowl gouge in and you turn it all about.

Re: Grinder location

#8

Re: Grinder location

john lucas

>Now that's a pretty good idea. I rarely use my planer and my grinder at the same time. I might be able to do that one.

Re: Grinder location

#9

Re: Grinder location

Barry Irby

>I have a small shop and have been considering one of these flip top carts. Right now I have my planer mounted on a base for a Delta jointer base I got at a yard sale and put wheels on it so it rolls out of the way. The grinder sits on my workbench/junk storage spot. The old jointer base just takes up space supporting the planer. If I made it a flip top cabinet it could store two machines in the same space.

I also want it to serve as a tool caddy or "butler" to hold my turning tools that I am working with.

On final thought, the bed of the planer has to be below the table on my table saw, because the lumber I am planing has to pas under the tablesaw. My shop is so small that when I hold one end of the board, the Devil has hold of the other end.

Re: Grinder location

#10

Re: Grinder location

Bill Neddow

>Put the grinder as far way from the wood chips as reasonably possible. The sparks off grinders are supposed to be "cool" (as opposed to "hot" sparks from welding. But this is not always true. My neighbour burned down his barn with these cool sparks. Besides the barn and hay, he lost three antique cars and about $200,000 of other equipment. Luckily, the horses were in the paddock. I was driving by when I thought I saw a little flame on the side of the building. I stopped, started to drive up the laneway toward the house and realized it reallly was fire. I banged on the house door to alert him, and by the time we ran down to the barn, about 500 feet away, the entire end of the barn was a raging inferno. When the fire department arrived 5 minutes later, all they could do was stand back and watch.

I came home and moved my grinder. I consider the extra couple of steps good exercise and really cheap insurance.

Re: Grinder location

#11

Re: now you got me started.

Allen Neighbors

>You guys are some of my favorite idiots!! FOFL

How drab would life be without such as you. :o)

Allen

Re: Grinder location

#12

Re: Grinder location

Allen Neighbors

>John, I have my Grinder on a rolling stand (about 24"x24" footprint), combined with my sanding stand (tall). I spin it around when I'm turning, in order to stay sharp. Then spin it around the other direction (due to the electric cord) when I'm sanding, to get to the sanders and paper.

I'll post a pic later on if you'd like, but it works for me. I had to put a chunk of railroad track on the bottom to counteract the weight of the grinder.

Allen

Re: Grinder location

#13

Re: Grinder location

Carole Valentine

>LOL! I always did want to take ballroom dance lessons. Don't tell me I can even learn THAT at WC?!!!

Re: Grinder location

#14

Re: Grinder location

Clay Foster

>John,

Get rid of the jig and learn to sharpen free hand. You will also become a better turner.

Make handles that you can remove the gouge to sharpen it. Then you won't have to pack a lunch to swing that long handle around the shop.

Re: Grinder location

#15

Re: Grinder location

Nelson

>First you cut your pony tail off, next you will be buying a gig!

Re: Grinder location

#16

Mobile Cabinet w/DC

Peter Teubel

>I put mine on top of a cheap Craftsman rolling tool cart (non-ball bearing slides). In addition, I added a fold out shelf for turning tools and a small shop vac in the base to catch the grinding dust. Notice that I put the business end of the grinder on the OPPOSITE side of the drawers. This keeps the contents of the drawers clean.





Re: Grinder location

#17

Re: Grinder location

Bob Elliott

>John,

I cut 12 �� off my Wolverine arm. That makes it a little less than half its original length. The shorter arm is used with the Vari-grind. The only time I need the full length arm is when I sharpen a roughing out gouge or perform the blunt traditional type grind on a bowl gouge. This dual set-up will save space in your shop. I bought the 2nd full length Wolverine arm from Highland Hardware (yes, these items can be purchased separately).

The grinder stand base is an old school bus brake drum on wheels. Those wheels came from a huge 600-800 lb. microscope. I had the upright portion fabricated. This thing is so heavy, it stays put while grinding and can easily be moved about the shop (or outside).

The grinder is kept to the left of my lathe, a few steps away.


img

Re: Grinder location

#18

closer view 

Bob Elliott

>


img

Re: Grinder location

#19

Re: Grinder location

john lucas

>Clay I sharpen some by hand and some with the jig. My big gouges do have removeable handles(that I learned from you I'm pretty sure0. Still even sharpening by hand requires that you swing the tool in a pretty good arc. It does do away with the long wolverine jig arm.

Re: Grinder location

#20

Re: closer view

john lucas

>Bob I was atually thinking about cutting the arm even shorter so it would work well with the verigrind and then making the longer portion re-attachable by makeing a metal tenon. Thhis would allow me to use it full length on the rare occasion when I want to use it.

Re: Grinder location

#21

Good ideas to ponder-thanks guys

john lucas

>

Re: Grinder location

#22

One more thing...

Bob Fawcett

>I made a stand similar to the one in Bob's pic. The wood under the grinder projects about 3" further. I cut some blocks from scrap that are about 3" thick by 4" deep and tall enough to position the tool at the wheel. The bottom is attached to 3/4" material. There is an angle across the top. I can clamp the block to the "table" under the grinder. This gives a solid platform for my roughing gouge or other tool that needs an angle of 45 degrees to the wheel.

I'll post a picture when I can.