Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Genreal 260 opinions, value?

Posts

Genreal 260 opinions, value?

#1

Genreal 260 opinions, value?

Jake (SoMN)

>All,

I have an oportunity to purchase a general 260 Vs (reeves drive) lathe. It is set up currently as a 12". It has a lot of tooling including an outboard tool rest, multiple faceplates and extra rests and banjos. It has seen minimal use.

any ideas on value, and general opinions. I am currently turning on a Conover with step pulleys and am curious if it worth the money to upgrade.

I would want to put the riser block kit on it and mostly turn bowls.

It seems like a well built machine, but don't know much about the reeves drive. How does it work with a riser block and under the loads of bowl turning?

It seems all lathe manufacturers have left this type of design behind. Is is difficult to turn the backside of bowls with doing single mount faceplate turning due to the large cabinet?

Thanks much for your patience and opinions.

Jake

(remove the 2 for email)

Re: Genreal 260 opinions, value?

#2

Re: Genreal 260 opinions, value?

Ruth Niles

>I have a General 260 but it's the electronic variable speed. These machines are well built, you don't see many used ones for sale which tells me owners are satisfied and don't trade up often. I did have a 160 with the reeves drive, I traded up because I did have a lot of problems just with the reeves drive however, I do think it was that one particular machine and not all reeves drive lathes.

I can't comment on the riser block with the reeves but I don't see where it would have anything to do with it, you would merely get a longer belt. The lathe would operate the same.

I love my green machine!

Re: Genreal 260 opinions, value?

#3

Re: General 260 opinions, value?

Bill Howatt

>I can't really answer your value question or make an informed comment on General's mechanical VS system other than in the school where we hold our club meetings there are 3 lathes like the one you describe and they are always working.

I have a General 26020, 20" swing, with the electronic variable-speed and if I were to do what I consider an upgrade it would only be to something in the price range of a Oneway. My General costs about half of what the equivalent size Oneway costs. I have no intention of upgrading and see my General as being the last lathe I buy.

I agree the design is dated but it is very robust where it counts. It doesn't have the rotating headstock capability and this can be nice for making bowls but the headstock always stays in good alignment. Since on my 20" machine the bed is low relative to the spindle, I don't find "bending over" the bed when necessary to be much of a problem but I'm sure others would differ.

If you plan on putting in the riser blocks you are going to have to factor in the costs of making your banjo(s) the right height unless it is included in the kit. I can't recall if the swing is a bit larger when turning outboard . You might consider setting it up to turn bowls outboard so you don't have any bed to get in the way at all. Be aware that the outboard spindle thread is 1-1/8", LH whereas the inboard is 1-1/4" RH, so you need to have the appropriate chuck adapters or faceplates depending if you are inboard or outboard. It sounds like you may have this stuff in the package. Does it include the outboard bed piece?

It would be fairly easy to change the motor and install a Variable-Frequency Drive controller to have electronic variable speed in the future. Naturally, it will cost a few hundred to do this!

Not sure about you cabinet comment on turning bowls, I find the headstock is usually the culprit when I am trying to get behind something and I consider the General's headstock to be better than many in terms of size for this problem.

Hope this helps a little,

Bill

Re: Genreal 260 opinions, value?

#4

Re: Genreal 260 opinions, value?

Bill Crommett

>Jake : The only complaint that I have about my 260 is that it was not well concieved when it came to adjustment threads. Specifically, because they used course threads on the toolpost lock , I need to use a cheater pipe to keep the steady rest from turning. The rest is great .

Bill

Re: Genreal 260 opinions, value?

#5

Re: Genreal 260 opinions, value?

Jennifer@Indy.USA

>Jake I have the General 26020 electronic VS and love it. If the size of the lathe and the prics is within your needs, then I don't think you'll be sorry you bought it. The General machines are built like tanks.

I love my General!

Jennifer

Re: Genreal 260 opinions, value?

#6

Re: Genreal 260 opinions, value?

Anthony Y

>It's great machine for fifty year old technology. As with all these mechanical vs machines the low end speed will be a bit high for large bowls. I bought my 12" + riser = 20" machine VFD machine for $1750 6 or 8 years ago. If it's a nice machine $1200 or less.


img

Re: Genreal 260 opinions, value?

#7

Thanks for all your help!

Jake (SoMN)

>Looks like I am going to bite the bullet and get a new lathe. Now to get rid of the Conover.

Jake