Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Lamp Augers

Posts

Lamp Augers

#1

Lamp Augers

Ron McKinley

>I bought a lamp auger months ago but have never used it. There were no instructions with it but it seemed pretty straight forward. Then a few weeks ago I ran across a discussion of the proper way to use an auger which surprised me. So, I copied and pasted the information into a Word document and filed it under Woodturning�I thought�but now I can't find it�can't ever find a pencil either! Did a search on WC and came up with nothing. Now I have a lamp-making project coming up and need to know the proper way to use this tool......Thanks, Ron

Re: Lamp Augers

#2

Re: Lamp Augers

Jorge Castaneda ~ Downeast Maine

>Ron,

It is very easy, you need to have a live center with a cup and a point, you mount normally and when you have the inprint of the cup on the piece, back the tailstock, remove the point and remount; you need to have an auger that matches the hole in your live center, so all you have to do is send the auger trhough the tailstock and back out often to let the shavings go or you burn the auger.

I mount a square piece in a chuck and if the drilling is going easy just drill trough from one end to the other, if the going is rough, you may want to go halfway, flip the piece and finish from the other side.

mis dos centavos

Jorge

Re: Lamp Augers

#3

Re: Lamp Augers

Ron McKinley

>Thanks for your 2 cents worth Jorge. Sounds like it's right on the money! ........Ron

Re: Lamp Augers

#4

Re: Lamp Augers

john lucas

>Ron If the lamp isn't too long you can mount it in a chuck and then just bore the hole without the tailstock. I use the tool rest to keep the auger from bouncing too much. Either way you need to push the auge r in gently so it won't follow the grain. Then remove it often to clear the sawdust.

If your lamp is too long for the auger, reverse the piece and drill from both ends. If you don't have a live center with removeable point you may be able to drill from the headstock end if you mount the lamp on a faceplate that has a hole in the middle or in a chuck. Of course you need a hollow headstock spindle to do this.

Re: Lamp Augers

#5

Re: Lamp Augers

Allen Neighbors

>Ron, what is a lamp auger? I would guess that it is just a long drill bit, is that right? 'Auger' makes me think of an auger like they use to move wheat or seed through a pipe at long distances, or like the auger on the front of a combine. And then there's those bits that my Dad and I used to use in a Brace (Brace-and-Bit). Is that what they look like?

I've never seen one, that I know of at least, so I can't answer your question. I hope someone else does, though, because I may want to make a lamp someday, and I'll need to know. And now I'm curious, too.

Allen

Re: Lamp Augers

#6

Allen,

W.C. Turner

>Look at Packard's, & probably Craft Supplies also, to get a look at a lamp auger.

W.C.

Re: Lamp Augers

#7

Re: Lamp Augers

Ron McKinley

>Hi Allen: It's a long rod about 3' long with a cutter on one end and a handle on the other. It goes through a hollow center in the tailstock and you just push it through like a drill bit. That's about all I know now. In a few days I can tell you how it worked.

I made a lamp before I had this thing and I simply routed a groove in both sides of two boards to equal about 3/8" total, then I glued them together to make the blank. But had to carve two wooden plugs to plug both ends so I could turn the glued-up blank. Worked pretty well but didn't quite get it centered on both ends but it worked out fine.

Re: Lamp Augers

#8

Re: Lamp Augers

john lucas

>What makes a lamp auger different than a drill bit is it only cuts with one flute, not 2 like a dril bit or standard drill auger. The fact that it only cuts with one flute is what helps it track in the center rather than following the grain of the wood. This is how metal cutting boring bars work. You do have to push lightly and let the bits cut. I found that sharpening the bits to almost razor sharp helps.

There are other ways to drill the holes but it's always hard to keep them centered. My favorite method before the lamp auger was to drill a hole about 4" deep in one end using the drill press. Then drill a hole in a board and put a dowel in the board that fits your drilled hole. Center this on the drill press table and clamp it down. Now place the hole you drilled in your lamp blank on this dowel and drill another hole in the other end. This method aligns the 2 holes exactly. Then take a longer drill bit and connect the 2 holes. I use a 3' drill used for running wire in houses. You still need to drill about half way from both ends and sometimes it still doesn't connect. Be patient and feed the bit slowly and you'll get the holes connected.

Then mount the blank between centers so the holes are centered and start your turning.