Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Katalox

Posts

Katalox

#1

Katalox

tm

>I live in Southern California and in just over two years of

spinning wood I have tried a fair number of exotic timbers.

I'm extremely fortunate to have a fairly large variety of species

and number of exotic wood dealers in my area.

Katalox or Swartzia cubensis could be one of the hardest most dense

materials I've ever worked with... it is almost like stone.

Try the link for a factsheet & images

http://www.hobbithouseinc.com/personal/woodpics/katalox.htm

Because I have some problems with my hands I use a 4 screw

faceplate instead of single screw chuck to initially mount my

bandsaw-rounded blanks and rough turn and then shape a tenon

for reverse chucking into a talon 4 jaw scroll chuck.

I drilled pilot holes into my Katalox blank and used

a 1 1/2 inch wood screw and broke a couple of the screwheads off

with my cordless drill and #3 phillips bit.

After a few choice expletives I realized one mistake

I made ( and should have known better ) was using

screws that were previously used. Metal fatigue.

A dab of beeswax is something my grandnfather used to use

and something I should have remembered to use.

I'm trying to figure out what else I might do when

I retry screwing on the faceplate.

Maybe I should just glue a wasteblock on.

I'm still stuck with the problem of extracting

the broken off shanks of the screws.

The Katalox was touted as an economical substitute

for ebony... but time wasted and wear and tear on hardware

and yours truly kind of balances things out in the long run.

Thanks for any ideas,

tm

Re: Katalox

#2

Re: Katalox

eliot d

>I have found that sheet metal screws are better than wood screws and that the best way -- by far -- to get them in is to use a CORDLESS hammer drill. These are usually very expensive, but , believe it or not, Harbor Freight sell an 18 Volt cordless drill with a hammer setting for $29.95! And never mind what people say about HF, it works just fine. It's on the heavy side, though, so you wouldn't want to work with it all day over your head, or whatever. But for hammer drilling faceplates, I think it's perfect.

Re: Katalox

#3

Re: Katalox

Rick Allen

>I have had that issue with Brazilian Cherry. I tried drilling different sized pilot holes in the cut-off to determine what size pilot hole to use. The other thing that you could try is to drill, tap and use a bolt instead of a screw. As for getting the broken screws out, I find the easy outs tend to be to large for the size screw I use (though I have been successful on a couple of occasions. Now I drill holes around the broken screws (always seams that if I break one screw I will break more than one) and use a wood chisel to get the screw out.

I generally mount my blanks between the jaws of the chuck and the live center for initial roughing. That's right no screws to break.

Re: Katalox

#4

Re: Katalox

Carole Valentine

>Your Dad was right - a little beeswax or even soap works wonders when driving a screw in hard wood. As for getting rid of the screw shanks, I had to do this recently. On the advice of some WCers, I mounted the piece between centers and turned a tenon. I chucked it using the tenon, then, using a parting tool, cut grooves as close as was comfortable on each side of the offending screws to a depth of about 1/2". A chisel made quick work of the remaining "ring" of wood next to the screws and allowed me to get a good grip with vice-grips to back the screw shank out. I had previously tried the drill-a-bunch-of-holes-around-it thing and that was an exercise in frustration.

Re: Katalox

#5

Re: Katalox

OB O'Brien

>tm; Stay away from the wood screws and sheet rock screws on a faceplate. They have weak shoulders just under the screw head and will end up hurting you. Pick up some SPAX screws. They are blue, self threading and much stronger than sheet rock screws. Another good alternative is concrete backer board screws. They are very similar to the SPAX screws.

Another way to hold your exotics like Katalox on a face plate is; Put your faceplate on a piece of scrap/waste wood as normal but then put some double sided carpet tape between your waste wood and the piece to be turned. Clamp them together between centers really really tight for a long time, maybe 1/2 an hour or so. You will find it is really difficult to separate them with the tape between them. It also doesn't leave any marks on the bottom of your piece.

And last, countersink both sides of the holes in your faceplate. This gives a small relief space for the wood that is pulled up from the screw to go. Makes the faceplate contact with the wood more square and the whole rig run true. Hope all this helps with your turning. Let me know how it works for you. OB

Re: Katalox

#6

Re: Katalox

Barry Irby

>Two or three thoughts.

Try either sheet metal screws or Tapcon screws. (Lowes, HD etc ahs them.) The Tapcon screws are made for screwing directly into concrete and are very hard. I don't think they will fail. I like Phillips drive for this and its hard to find sheet metal screws with Phillips drive, but Tapcon has the Phillips drive already. I put a very slight counter sink in the backs of my face plated to center the screws in the holes.

Elliot, Is the Harbor Freight Cordless driver a rotary impact or linear impact? The hammer drills made for drilling in concrete are linear and hammer in and out, but the ones for screws are rotary. I have a twelve volt rotary screw driver and if you weren't breaking screws before, you will now. Don't get me wrong, its a great tool, you just need excellent screws.

If you are going to cut the foot away later, why not leave the screws in place? Grind them off flat and remount the faceplate and keep going. Don't forget them though, you might run into them at an inopportune moment.

My grandfather used to run the screws through his hair to lube them. yet another use for Briltene (sp?).

Re: Katalox

#7

You must.....

W.C. Turner

>be referring to "Brilcreme" Their slogan was "A little dab'll do you" Showing my age again!

Re: Katalox

#8

Re: Katalox

robo hippy

>To prevent broken screws one thing you can do is use the clutch/torque adjustment on your drill. A lot of people set it to the highest rating which can break screws off even in softer woods. You seldom need the highest torque setting.

Another method to get away from face plates is to use a forstner bit and drill an appropriatly sized hole for your chuck jaws to expand into. Turn the bottom, then reverse. I can turn bowls up to 16 by 6 with no problems this way. You can bring the tailstock up for additional support if you want to.

robo hippy

Re: Katalox

#9

Re: Stupid question

RobinCorell

>I have learned not to assume anything so that is why I am asking this particular question. are you drilling a pilot hole with a tapered drill bit? on most woods it really makes little diferense with a wood screw but on really hard stuff the unthreaded portion of the shoulder on a wood screw is tappered and can really bind if the pilot hole dosent match.

There have been a lot of coments about using tapcons or other hardend screws. I was always taught to use a softer screw because it is preferable to have it bend rather than break.

As far as the broken screws, I think I read somewhere that Carole is the expert at how to remove them.

Robin

Re: Katalox

#10

Re: Katalox

Jim King

>When all else fails this works well. We work with woods like Katalox everyday and never a problem.


img

Re: Katalox

#11

Re: Katalox

GaryG in MD

>My thoughts run with Barry's:

If you were screwing the screws into what would eventually become waste wood, there is no reason to remove them. Just rotate the faceplate for the next batch of screws and mark the locations of the broken ones so you don't accidentally get into them.

Let us know how it turns out, Gary

Re: Katalox

#12

I agree plus,

Mike Nelson

>Can't remember last time I used a faceplate, use a four prong morse drive in your chuck with about 1/8" sticking out past the face, then put one of those live centers with the hole and point on the tail stock and you can get a tennon or mortice on anything.

I agree with Rick, why waste the time and expensive wood!