Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Turning pressure treated lumber

Posts

Turning pressure treated lumber

#1

Turning pressure treated lumber

Marym

>Hi everyone,

I have a job coming up where I need some weather resistant spindles in a larger diameter (5 1/2"), and I was thinking of using some pressure treated 6x6 posts for these. Is there any problems doing this from this lumber? Has anyone here tried this?

Any thoughts on this would be greatly appreciated!

Thanks

Re: Turning pressure treated lumber

#2

Re: Turning pressure treated lumber

Leppikallio

>Here in Finland all pressure treated lumber is pine and if available 6x6" (or 5 1/2" diameter) lumber if available would split like crazy when drying. Is painting or other "weather proofing" out of question? How about turning that from laminated larch/tamarack beam (or some of your wonderful weather resistant timbers)? Larch/tamarack is about as good as pressure treated pine, at least in here...

Re: Turning pressure treated lumber

#3

Re: Turning pressure treated lumber

Rick Allen

>Danger, Danger Will Robinson

There are a number of woods that work well outdoors which do not have chemicals added to protect the wood but harm you. I wouldn't want to expose myself to all those "protective" chemicals.

Redwood, Eastern Red Cedar, Western Red Cedar, Cyprus, Honey Locust, White Oak are all good outdoor woods, especially when an outdoor finish is used like Cetol.

If you insist on turning pressure treated lumber then protect yourself like you are doing asbestos abatement.

Good Luck

Re: Turning pressure treated lumber

#4

JL

Re: Turning pressure treated lumber *LINK*

JL

>Other than the problems of turning pine :)? If it's ACQ treated, I don't see too much of a problem (that's the "new" treatment). I would be really cautious if it's CCA treated. In any case, wear a dust mask or preferably a respirator. Collect the shavings and dust separately from your other turning debris - they aren't going to mulch very well. Don't leave the dust/shavings on the bed of the lathe - I figure if it requires special steel fastners that won't corrode, it might not be nice to a lathe bed.

Read the MSDS (material safety data sheet). If you scroll down on the Great Southern site, you'll find MSDSs for ACQ and CCA wood among others.

Have fun and let us know how it "turns out".


Great Southern Wood

Re: Turning pressure treated lumber

#5

Re: Turning pressure treated lumber

Marty - St. John's, Newfoundland, Canada

>Marym

Why would you go through the expense of buying 6x6 pt and then turn away the wood that is soaked in the chemicals? If you look at a cutaway of pt wood the chemicals do not penetrate deep into the wood. You would be removing the material that you are paying the extra money for in the first place. As others have mentioned use a cedar,tamarack,cypress,etc. that have great insect and weather resistance.

hope this helps ...

Marty ...

Re: Turning pressure treated lumber

#6

Not recommended

Jorge Castaneda ~ Downeast Maine

>You willl be breathing and your skin will be covered with arsenic.

Re: Turning pressure treated lumber

#7

Re: Not recommended

Carole Valentine

>I believe the arsenic was phased out of the treatment process. That's not to say that there is not some of the old "arsenicky" stuff still around! I would be cautious about any sort of treated wood.

Re: Turning pressure treated lumber

#8

Re: Not recommended

Edward in Vancouver

>Even if you did turn the p/t posts, the treatment only penetrates about 3/4"- 1" in the wood, so it wouldn't be worth the hassle.

Re: Turning pressure treated lumber

#9

Re: Turning pressure treated lumber

Bill Hale / Woodspinner

>As Leppikallio said, use good weather resistant wood. There are to many better woods than PT.

Good wood, a good finish and you are way ahead.

Good turning and above all be safe.

Bill in Dolores, CO

Re: Turning pressure treated lumber

#10

Personally, I see BIG potential health risk...but

Craig Daymon

>there is another, new pressure treated lumber that I believe might be very safe for turning. (Though still adviseable to wear some dust protection.) The product is called, "Timbersil", but I don't recall who makes it. If memory serves, it is a plastic impregnated lumber, so it ends up weather-proof (loooooooong-time), but should be safe to turn. (Probably safer than turning corian pens.)

-Craig

Re: Turning pressure treated lumber

#11

And Also...

George (Oxford, NC)

>PT wood is very wet when you buy it. Once turned and dried it will warp/twist. If you hold on to it until it dries, you will have checks and cracks all along the length.

George

Re: Turning pressure treated lumber

#12

Wow...I guess I will reconsider-now where to buy?

Marym

>Maybe another wood instead is the way to go. I didnt realize it would be that dangerous, but enough warnings here tells me so.

Can someone tell me where I might find large enough blanks for this job, in New England, out of some of the woods mention by others? I would need 6x6x40" or so blanks, I suppose in either white oak, cedar, or others. I suppose pine would be okay too, as it will get a finish on it, but since the house is right across the street from the ocean, I was trying to come up with something that would be as weather resistant as possible.

Thanks for all the replies.

Re: Turning pressure treated lumber

#13

Re: Wow...I guess I will reconsider-now where to b

Mike Nelson

>I glued up 2X8 utility fir (you can cut out the bad sections) with titebond III, and turned 6" fence-post fenials. Prime all sides especially ends twice and couple coats ext. acrilic latex.

Re: Turning pressure treated lumber

#14

Will it be painted, stained, or clear coart?

Ron in Drums PA

>

Re: Turning pressure treated lumber

#15

Re: Will it be painted, stained, or clear coart?

Marym

>They will be painted, with some sort of decorative finish, to look old. I am not involved in the painting myself. I have to rough them up to give them some age, and then a painter is taking over.

Thanks...

Re: Turning pressure treated lumber

#16

Re: Turning pressure treated lumber

Brian Simmons, Heflin, AL

>Saw a show on HGTV about 5 years ago. It was about a fellow in Georgia that turned porch posts. He bought 1x2 lumber because it was easy to find clear clean wood. He glued up the 1x2's to blocky round shapes and turned 8, 10, and 12" diameter posts. He sold them for $300-$500 each.

Another option is something like 100% recycled plastic timbers, I found a list in this pdf, pages 11-19, some in NE.

http://twilight.saic.com/ap/landscaping.pdf

Re: Turning pressure treated lumber

#17

On the contrary...

Peter Teubel

>Every PT beam I've ever cut is treated 100% thru the wood (SOMEWHAT less in the middle, but still treated..)...even 6x6 beams. That's the whole idea with PT lumber vs a brush/spray on preservative.

Re: Turning pressure treated lumber

#18

Re: Will it be painted, stained, or clear coart?

Ron in Drums PA

>Well, if it's painted you don't need to worry about PT wood.

I'd glue up some poplar to get the size you need.

Titebond III is almost waterproof and should work well for this.

Sand to 150, and let the painter take care of the rest.

Re: Turning pressure treated lumber

#19

Re: Will it be painted, stained, or clear coart?

Jorge Castaneda ~ Downeast Maine

>I would stay with a wood that is weather resistant, like red cedar or philipine mahogany, both found as decking in the lumberyards for around 1$ a running foot for a 5/4" x 6" (1 1/16 x 5 1/2 ") laminate to the size you need and turn.

$0,02

Jorge

Re: Turning pressure treated lumber

#20

Enviro-Safe Lumber *LINK*

Richard Jones

>Product is called Enviro-Safe, a "new" treatment process. Not certified yet for ground contact, but can use for everything else. As a building inspector, I see a lot of it here, as one of the local lumber companies is using the process.

Wood seems to be a bit punkier than if you treated it like normal PT or ACQ, but seems to be lasting OK.

I don't think pine is the best choice for a turning, even tho' the EnviroSafe stuff I've seen doesn't seem to split as much as its' ACQ cousins..................

BTW, the "old" PT lumber is still available and is still being made for many commercial applications. Most stores don't stock it anymore.

Rich in VA


EnviroSafe Wood Products

Re: Turning pressure treated lumber

#21

Brad Vietje

Black Locust

Brad Vietje

>Mary,

I'd Use Black Locust, or one of the Cedars. Black Locust is all over the place, but not commonly sawn into dimensional lumber. There's a fellow in Western Mass. (Colrain, I think) who goes by the Native American name Blue Sky. He advertizes Bl Locust lumber for environmentaly friendly construction and as an alternative to pressure treated chemicals. He advertizes in various magazines in the Pioneer Valley, so I could find his contact info if you are interested.

Safe spinning,

Brad Vietje

Newbury, VT