Mini lathe for sale (!?) *LINK*
Dave Winters, Steamboat Springs, CO
>Perfect for small basement shop.
http://www.woodweb.com/exchanges/machinery/posts/409136.html
Knowledge You Can Build On — Est. 1998
Mini lathe for sale (!?) *LINK*
Dave Winters, Steamboat Springs, CO
>Perfect for small basement shop.
http://www.woodweb.com/exchanges/machinery/posts/409136.html
Re: Need a crane to get it down there..
JL
>
Loopty loop
John Lucas
>Anybody remember the Loopty Loop. It was Joe Looper's lathe he had at the Appalachian Center for Crafts. It was a modified metal lathe and was almost that big. I think it was 54" swing. I think the new owner might sell it if anyone wants' something that big.
Saves the time.....
Thomas Skaggs, Foothills of Mount Level
>....of cutting up the tree into blanks. Just mount the entire tree on there!
Tom
Can you imagine that at 1000RPM?
steve antonucci
>I think it would be like turning in the old Bose commercials! Wind in your face, and 4 pound shavings flying 30' over your head...
Still... I find myself wanting it :-)
Steve
Re: Can you imagine that at 1000RPM?
John Lucas
>Steve My friend Joe Looper had purchased an 8 foot faceplate lathe with a 20 horse motor. It was still at the metal shop when he passed away so I don't know what happened to it. The faceplate was 3 or 4" thick. It was a massive machine. Imagine that going 1000 rpm. I'd be nervous at 2 rpm.
1000RPM, 60" dia = 161 MPH?
Devo
>Double Check my math, but, that would be a mile of travel ever 22 seconds, 161 miles in an hour :)
Re: Math double checked
Thad
>188.495"/R = 188,495"/minute (at 1000RPM)
188,495/63360 = 2.97 miles/min (63,360"/mile)
2.97x60 = 178.2 MPH
approx 4.28 times faster than 14" at 1000RPM
I did it in round numbers before at 180mph
steve antonucci
>any way you look at it, it would scare the daylights out of the manliest man... or womanliest woman... or anyone with a shred of common sense...
Steve
Re: 60 rpm is not too bad
RobinCorell
>I used to turn on a large faceplate lathe. It was built in house by a couple of long since retired paternmakers and had a 11' diameter faceplate and a coresponding slot in the floor for it. I don't remember the hp of the motor, but it was substaintial I'm sure. power was run through a chevy 3 speed with a hurst shifter complete with an 8 ball knob, how many lathes have one of those? It was not really that scary to turn on because it only turned at about 50 or 60 rpm, at least that is the only gear I ever saw it used in. It did have a sort of rythem to it with a slight flexing of the floor and the floor stand tool rest holder. strangely it didnt seem to affect the acuracy of the turnings. I never experianced any catches or other mishaps, though a friend did snap a 24" tool rest. I think it hurt his pride more than anything else, but then again this is the exact reason why I think all tool rests should be made out of cast iron.
Most of what we turned on that monster were the patterns used to make aluminium rings that were used as the molds on the ends of large concrete sewer pipe. I always wondered what creative uses a lathe like that could be used for and often wondered about the fantastic bowls something like that could make.
Robin
I need a Hurst shifter on my Nova...
steve antonucci
>and a big block 427!
Great story. I broke a tool rest on my old Craftsmen lathe (what a shock, a broken Crapsmen!) and I can only imagine the look on someone's face when their "barrier" disappears leaving them within inches of harms way.
Steve
Never turned a sewer pipe fitting before...