Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

hollow form question

Posts

hollow form question

#1

hollow form question

tm

>Pretty basic problem I'm having but I could use some fresh ideas

on how to clean shavings /dust out from inside a hollow vessel.

I have a really fine O'Brien hollowing rig that works like a charm and I want to get my pieces micro-clean inside for finishing.

I've tried a paintbrush but the dust / shavings mix gets dense and compressed against the inside wall.

I'm toying with the idea of making a mini wand to connect to a shop vac to slurp it out.

Any ideas?

Many thanks,

tm

Re: hollow form question

#2

Re: hollow form question

Norm Smith in Nova Scotia

>Hi TM,

I use a small air compressor and blow them out. Works great.

Norm

Re: hollow form question

#3

Ric Taylor

Re: hollow form question

Ric Taylor

>If you don't have a compressor, you can blow them out with a regular soda straw. Works fine, and lasts a long time.

Ric

Re: hollow form question

#4

Re: hollow form question

Barbara Gill, Remlik VA

>That is a good idea. I use my shop vac with the wand held at an angle to create a vortex to suck out the chips. A straw would be much quieter. :-)

Re: hollow form question

#5

Re: hollow form question

Carole Valentine

>I don't have a compressor yet (looking for one) but on my small pieces I use that canned air. Works great. Also, if you use steel wool in the finishing prcess, even if only on the outside, you will be surprised at the amount of steel wool that gets inside the vessel. A small magnet dropped inside and rolled around will come out looking like it just bought a new fur coat!

Re: hollow form question

#6

Ric Taylor

Re: hollow form question

Ric Taylor

>Use the kind of straw that lets you bend it at a 90 degree angle. Otherwise, if you blow straight in, you get a face full of chips.

Ric

Re: hollow form question

#7

Re: hollow form question-O'Brian?

georgetroy

>I use an air compressor and just blow out shavings. You could also use the vac to suck or blow or the shavings. I would like more information about the O'Brian hollowing system. Not familar with it. Any photos, or other information? GT

Re: hollow form question

#8

Some ideas

OB O'Brien

>Hi TM; Glad to hear the hollowing rig is working OK for you. Here's some ideas. Get a long handled small spoon, like a tea spoon or one of those long plastic ones you get with a milkshake. You can scoop them out with it. Another way would be to bend a long handled small fork into a rake and rake them out. Of course, don't try either of those while it's turning. Another idea would be to tape a plastic tube to the top of the boring bar and run it out to where you can blow the chips out with your breath or connected to a small compressor. This might work best for you as it might work while your turning. Think I will put one together today and see if it works. Iv'e got some hollowing to do for a demo next Saturday in Mobile Alabame. Cya OB

Re: hollow form question

#9

Re: hollow form question-O'Brian?

OB O'Brien

>Hi George; It's a hollowing rig I make. It's a scaled down version of the Jamieson captured system. It's sized for the mini lathes and comes with a laser, instructions and everything else, ready to use.


img

Re: hollow form question

#10

Steven Antonucci

Vacuuming doesn't work very well

steve antonucci

>I tried to vaccum out the inside and it didn't work weell at all. For starters, once the hole is smaller than the diameter of your hose, you can't get inside. Second, vacuum needs to remove air along with chips, and there isn't enough airflow to create suction. Basically, nothing happens.

Buy a compressor. I tried all of the spoons and fingers and such... I specifically bought a compressor for one purpose- to blow shavings out of hollowforms, and it is hands down the best way to do it.

Steve

Re: hollow form question

#11

Re: hollow form question

robo hippy

>Before I had a compressor, I would take a 1/2 inch piece of irrigation pipe, and blow out the chips. Note, make sure that you don't have your mouth on the tube when you inhale. You can also remove the turning from the lathe (chuck and all), and shake the shavings out. I also bought the compressor for blowing things out, and was surprised to find all sorts of other uses for it.

robo hippy

Re: hollow form question

#12

Re: hollow form question

Mike Nelson

>As I mentioned to Carole on her air compressor question, Big Lots carries (sometimes) a thin red lever handled blower that snaps on the end of air hose, it has a 9" or so 1/4" tube slightly bent at the front, it has 'AirAce' stamped on the side of the thin handle (I use the long trigger to hang it on my lathe. If your lucky enough to find them on the shelves get two or three, dirt cheap and you'll love it. Mike

Re: hollow form question

#13

Dick Hines

Re: hollow form question

Dick Hines

>I use my compresser set at about 90PSI. Put your hand over the hole or you get a face full of hot chips.

Re: hollow form question

#14

Re: hollow form question

Frank Alvarez

>I use the air compressor in my right hand pointing the push button blower fitting into the hollow form and the vaccum line in my left hand with the last three fingers creating a cover over the top of the piece so wood shavings don't come out in my face. This works amazingly well and keeps the shop clean at the same time. While I turn, I keep the vacuum running hanging just below the the tool rest pointing up, so it's always handy and sucks up most of the other turnings also. The air line hangs on the front of my lathe so it's handy also. The way to stop the turnings from becoming matted on the inside wall( so that it has to be scraped off) , is to empty the hollow form frequently before the turnings become matted and are just loose inside.

Frank