Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Make your own quick change sanding wheel

Posts

Make your own quick change sanding wheel

#1

Make your own quick change sanding wheel

Dave Belser

>A while back ( ~ 3 months?) in a thread about sanding paper/disks etc. Someone stated that they had made a set of quick change hook & loop holders using Power-Lock sanding disks. For those that aren't familiar with the Power-Lock system, the disks are pretty rigid and have a plastic part on the back that snaps into a holder in your chuck.

I bought the starter kit a while ago, I also have a couple of the 2" Artisan holders from craft supplies. I much prefer the Artisan holders over the Power-Lock for any number of reasons I won't get into here.

The problem is that as the hook material wears, I've had to replace it on the two holders I have. The glue backing on the new hook material is very strong, but softens when the pad heats up. Also changing the disk all the time as I work thru the grades leads to having to discard a disk because the loop material has pulled off the back even thought the disk still has some life left in it.

So the benefits of a quick change system become apparent, the disk stays on the pad until the sandpaper is dead, because you are changing the pad when you change disks the pad doesn't heat up as much and has time to cool.

Being a Yankee (and broke), I have the parts from the Power-Lock (old disks and holder) and can afford to buy the hook material and buy or scrounge the foam, I'd like to make my own quick change set of holders.

The biggest question / looking for suggestions that I have is what to use for glue between the layers? I will need to glue foam to dead Power-Lock disk, and Velcro to foam. The disk needs to flex so the glue has to be flexible. Any ideas?

The other question is about the foam, I have some mouse pads that seem to be about right but are a little thin. What have other people use / any ideas on what to use?

I'll post a summary of this project when I'm done.

- Dave

Re: Make your own quick change sanding wheel

#2

Re: Make your own quick change sanding wheel

tek-Brunswick, Ohio

>Household Goop works great. I bought some from "The Sanding Glove". It is what they recomend for glueing replacement velcro, which I also bought from them. I've had good results with it. There are several kinds of GOOP make sure you get the one labeled Household Goop. Mine came in a Maroon tube. I use my spent Abralon pads as interface pads by glueing velcro over the spent abrasive. Tom

Re: Make your own quick change sanding wheel

#3

Re: Make your own quick change sanding wheel

Keith Newton

>I am not sure exactly what you are wanting to do, but I have used the high-tac spray contact cement for a number of things.

I saved the little plastic pad behind the sanding disk that came with the little arbor-tec cutter. Scuff the face with coarse grit, then spray it, let it thoroughly dry, then I use peel and stick that I punch myself. They have to be warm to remove.

I wanted even smaller, so I built up the end of one of the little penny size diamond disk for a die-grinder. I sprayed several coats to get a little build-up. It works great for sanding in detail carving.

Re: Make your own quick change sanding wheel

#4

Re: Make your own quick change sanding wheel

Barry Irby

>Dave, I started on this and got side tracked. (What's new, I have ADD)

I found you can buy the sanding disks from Industrial Abrasives for about $5 each. Unfortunately, they have round shafts. What I wanted was hex shafts with the quick disconnect cove in them. I'm too lazy to spin the chuck on and off. (So now I have ADD and I'm lazy, I did not get the Hyper-activity part.)

My point is, that it might suit you better to use those pads than to go through all the work of making your own. I have a friend that has a board near his lathe with about six two inch holes and about six three inch holes. The holes are about a quarter inch deep. Eh has a pad sitting in each with a grit on each, in order. He uses a drill with a key-less chuck. The only thing I see that would be better is to have the quick change chuck, but all the pads I find that have the hex shafts are way ore expensive.

Another thought. If you are going to have a disk for each grit, you could switch to PSA disks. I think they are cheaper. Since you would be leaving them on, there would be no issues with trying to remove and replace them.

And now you need to read the articles on making your own disks. If you do a lot of sanding, the mandrels are a relatively cheap part, its the sand paper that you use and throw away. You can cut your own for about a nickle or maybe ten cents each.

Re: Make your own quick change sanding wheel

#5

Re: Make your own quick change sanding wheel

Allen Neighbors

>Dave, I make my own sanders out of Rollerblade wheels and pads from old (or new) flip-flops... you know, those shoe-thingys that the little gizmo sticks up between your toes... they used to be called thongs, 'til someone changed the location of wear. :o)

After cutting the flip-flop to fit, you can let it be sanded to your desired thickness by holding it down on a spinning belt sander.

I use epoxy to glue the velcro on. And when the velcro wears out, I just sand it away on a 50 grit belt sander, and replace it with new.

Allen


img

Re: Make your own quick change sanding wheel

#6

Steven Antonucci

What do you use 60G on & why do you have 2 of 'em

steve antonucci

>Just wonderin ;-)

Steve

Re: Make your own quick change sanding wheel

#7

Re: Make your own quick change sanding wheel

Dave Belser

>Thanks Allen.

Now I remeber seeing this picture before. Flip flops sound perfect. Someone else suggested household goop. I might see if they have it at the hardware store or I'll just use epoxy. I'm makeing a quick change setup for my souix drill, but I'll keep your idea in mind if I ever decide to try free wheelers.

I'll try to post a recap of the this project when I get it done.

- Dave

Re: Make your own quick change sanding wheel

#8

Re: Make your own quick change sanding wheel by Al

Lan Brady

>Allen,

Your idea looks great. Have you posted a thread on how to make these? If not, now is a great time!

Lan

Re: Make your own quick change sanding wheel

#9

Re: What do you use 60G on & why do you have 2 of

Allen Neighbors

>Steve, when I'm turning wet Bois d'Arc, sometimes it's difficult to turn without splintering and tearout. That's what I use it on. I have two, because I don't have the grits in separate bins, yet, and when it gets filled up with gunk, I don't want to take the time to stop and change... I just grab the second sander.

Allen

Re: Make your own quick change sanding wheel

#10

Re: Make your own quick change sanding wheel

Allen Neighbors

>That household goop sounds good, too. I may try it next time I have to replace one of these.

Allen

Re: Make your own quick change sanding wheel

#11

Re: Make your own quick change sanding wheel by Al

Allen Neighbors

>Lan, I have once before, I guess you'd just have to do a search... it was before the Georgia Gathering.

I think.

Allen

Re: Make your own quick change sanding wheel

#12

Re: Dave, I apologize,

Allen Neighbors

>I wasn't trying to hijack your thread.

I would definately like to see your rig when you get it finished, because I need to rig up something to sand insides.

Allen

Re: Make your own quick change sanding wheel

#13

Re: Dave, I apologize,

Dave Belser

>No need to Allen, I'm not to possessive about my threads most of them are in pretty rough shape anyways (oh that would be my duds wouldn't it?). No offense taken, as long as your not one of them artist types....

- Dave :)

Re: Make your own quick change sanding wheel

#14

Dennis in Southern Oregon

Re: Make your own quick change sanding wheel

Dennis in Southern Oregon

>Dave, my favorite adhesive for things like that is "emblem cement". You can get it in auto supply stores among other places. Dennis

Re: Make your own quick change sanding wheel

#15

Re: Make your own quick change sanding wheel

Gary in Zirconia, NC

>I have tried household Goop and my velcro won't stay on. I let it dry 2 or 3 days. It comes off the first time I use it. It appears to be gumy or not dry. I think the heat melts it but not sure. Anybody have any suggestions?

Re: Make your own quick change sanding wheel

#16

Re: Make your own quick change sanding wheel *LINK*

Darrell Feltmate

>Dave

Sorry to take so long to chime in here, but why not go to my web site and see how I made these things?

Darrell


Woodturnings by Darrell Feltmate

Re: Make your own quick change sanding wheel

#17

Awesome Darrell!

Dave Belser

>Awesome Darrell!

Thats pretty much exactally what I'm doing. I Think I might have seen your info at some previous point.

So far I've picked up a tube of goop to use as an adhesive. I've had no luck with hot glue for other things in the past, the stuff I'm using just isn't sticky. I've got a little crafter's type glue gun the kind use to glue fabric and flowers to Styrofoam! What are you using for a gun and for glue sticks? I think hot melt glue from a gun would be easier than the Goop but the Goop sure feels like it will hold up.

I used the suggested flip-flop sole for a backing for the first few I've made but it's to stiff. The camping mat stuff is perfect. I have one and know exactly where it is - under my live in mother in-law on her couch/bed! Hummm, this could get interesting.

I'll still post a summary when I'm done.

My wife and I love Nova Scotia, in fact we have three road trips on line 1996 - 1998 at newww.com check it out if you want. I once got an excellent car wash in Turo! Lots of other nice stuff around there also :) If we ever get back to NS, I'll give you a heads up.

- Dave

Re: Make your own quick change sanding wheel

#18

Re: Awesome Darrell! *LINK*

Darrell Feltmate

>Dave

Glad you like it. I just use a regular glue gun and glue sticks from wherever they are cheap. The lst gun was 4.95 from the grocery store as I recall. It gets used for holding bowls on the lathe and all that kind of stuff. In my experience hot glue from a gun is next to useless for permanent wood working but for jigs or a strong temporary hold it is great. Just remember to let the gun heat for ten or fifteen minutes before use.


Woodturnings by Darrell Feltmate