Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Pen blank jigs anyone?

Posts

Pen blank jigs anyone?

#1

Pen blank jigs anyone?

Dustmaker Mike

>Howdy all. I have a 12" sander and was useing it to sand the end of pen blanks after they where drilled. I had a soft touch but was worried about not sanding the end at 90 Degs from the tube. So I was wondering what the rest of you used with a 12" sander? Any jigs I can make or maybe buy? Any pictures of the jigs?

Re: Pen blank jigs anyone?

#2

Re: Pen blank jigs anyone?

Ron in Drums PA

>Why not just get a barrel trimmer?

You didn't say if your 12" sander is a belt or disc sander. Either way if it has a miter gauge, just use that to keep things square.

Re: Pen blank jigs anyone?

#3

I have a pen mill

Dustmaker Mike

>this is for the woods that tear out from the pen mill. Or just a touch up on the end with out shorting the length.

Thanks

Re: Pen blank jigs anyone?

#4

12" Disk Sander

Dustmaker Mike

>

Re: Pen blank jigs anyone?

#5

Re: Pen blank jigs anyone?

George (Oxford, NC)

>I use an 8" disc all the time with a miter gauge. I check it every few pens with a square. It is usually right on, or at least close enough that the pen grains line up well. I have a pen mill but find it to be a pain to set up for each pen. Whether I use it in te drill press or the lathe, I have to put it in and take it out every pen for either the drill bit or the pen mandrel. With the disc sander, boom, boom, square and ready.

George

Re: Pen blank jigs anyone?

#6

Re: Pen blank jigs anyone? pic

gary s clarke

>Mike I use this jig for the ends of pen blanks and for making segments for bowls. Not my original indea, works well.


img

Re: Pen blank jigs anyone?

#7

Re: Pen blank jigs anyone?pic2 

gary s clarke

>


img

Re: Pen blank jigs anyone?

#8

You need to sharpen it

Ron in Drums PA

>Like this


img

Re: Pen blank jigs anyone?

#9

Re: You need to sharpen it

Jake Niedling

>Are you sharpening the flat side on the side of the grinding wheel?

Re: Pen blank jigs anyone?

#10

Re: Pen blank jigs anyone?

Bill Turpin in WNC mountains

>I made a removable scrap plywood jig for my Dewalt chop saw. It is attached with a couple of clamps. There is a back board with a stop block for repeatable lengths. A toggle clamp holds the cut-off piece of pen blank. The bottom board is wide enough so that the blade can come down the full amount and it still holds together. I stop the saw and allow it to coast to a stop, before I raise the blade. This keeps the cut off from being dragged back into the blade and messing it up. I will post a pic if anybody is interested. It is not pretty, but it works well.

Bill WNC mountains

Re: Pen blank jigs anyone?

#11

Re: Pen blank jigs anyone?

HarryB

>Mike, You want to make the ends of the blank square with the brass tube, and the brass tube is not necessarily parallel with the sides of the blank.

You need to make a jig with a piece of rod that fits snugly in the brass tube and is square with the sanding disk. The downside of this is that you need a different jig, or at least a different rod, for each different pen style you make.

Re: Pen blank jigs anyone?

#12

Pic , Please!

Clem Wixted

>

Re: Pen blank jigs anyone?

#13

Re: You need to sharpen it

Ron in Drums PA

>No, but I'm almost touching it.

Re: Pen blank jigs anyone?

#14

Re: Pen blank jigs anyone?

Ron in Drums PA

>Not necessarily. What you can do is "rough turn" the pen blank round so the wood is parallel to the tube. From there you can take it to the sander. Making sure the table is square, all you need is a miter gauge to square up the tube.

Re: Pen blank jigs anyone?

#15

Re: Pen blank jigs anyone?

eaglesc

>I"touch" up the sides of my pen mill,the same side that Ron shows in his picture.

The difference is I use a diamond stone I picked up at Lowes for $6.00.

I guess it's meant for knives or fish hooks.

The size is 1&1/2 x3" and has 90* edges.

I lay the stone along the side of the"flutes" and make the same amount of passes on each side.

Every once in a while I have it professionly sharpened.

The difference is night and day.

Shavings rather than dust with no burt edges.

Re: Pen blank jigs anyone?

#16

Thanks All

Dustmaker Mike

>I will make the chop saw jig. I sort of have one already but it is a bit scary. I have sharpened my Pen Mill but sometimes the wood wants to chip off at an edge so I do the finel bit with the sanding disk. I will try the miter gauge and the other jig shown and see if I can get a little better results.

Re: Pen blank jigs anyone?

#17

Correction

Ron in Drums PA

>I'm sharpening the flat side against the wheel