Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Dang it!

Posts

Dang it!

#1

Dang it!

Carole Valentine

>What do you folks use to hollow long-grain??? I usually hollow my vessels end grain, but I wanted this piece of dry Olive Ash oriented long grain and it is beating me and my Keltons literally to death everywhere except the middle of the vessel where it is end grain. I am having a particularly hard time getting a cut (not to mention a smooth cut!) between the shoulder and the neck. Should I be using some other type of tool?

Re: Dang it!

#2

Re: Dang it!

Peter Hyde

>When in doubt I get the Termite out! I find it works on both ens and side grain hollowing. If it's a slow process I might switch to my 1/2" long and strong bowl gouge. I don't have a Kelton so I can't compare.

Re: Dang it!

#3

Re: Dang it!

john lucas

>Carole I always fall back on my John Jordan cutters. Well actually scrapers. The 3/16" HSS cutter doesn't seem to care which way the grain is running. I do have trouble getting really smooth walls but it's just lack of experience. I use the same shape cutter on my Christmas ornaments and small hollow forms and don't have any trouble with these. for some reason when the form gets bigger I get clutsy with the hollowing. I guess it's because I don't do as many.

Re: Dang it!

#4

Re: Dang it!

Bill Hale / Woodspinner

>I use a DSS setup with a 3/16 cutter. At the end I put a scraper on it for the inside finish cuts. I also have made some special long bars to fit in the arm brace. I have a 3 ft. 1 1/4 SS and a 5 ft. 1 1/2 SS for those deep cuts. The only problem is the 5 ft. must weigh 50 lbs. or so. I can only use it for about an hour and my arms give out.

Good turning and be safe

Bill in COOL Colorado

Re: Dang it!

#5

Re: Dang it!

Carole Valentine

>I must be suffering from another senior moment. DSS? What's that? A 5' hollowing tool?! LOL I can see me using that. Sure!

Oh and please quit rubbing in the "cool" Colorado thing...you may find yourself facing a massive influx of sweltering coasters! ;)

Re: Dang it!

#6

Re: Dang it!

Ed Heuslein

>Howdy Carol: If this piece is typical of your smaller turnings, here are a couple suggestions. A small (Sorby) "Swan Neck" type tool which holds a 3/16" bit would work well. Also, Bob Rosand uses a tool he makes for his ornaments. It's very easy to make. A piece of square 1/4" cold roll about 7" long. Cut the end off at a 40 degree angle (approx) and silver solder a 3/16" bit to it(I usually cut my tool bits in half or thirds to do this). Easier yet, send me your address and I'll send you one (I have a bunch made up all the time for club members). You can use one up to about 1-1/2" deep - or deeper if you can get your tool rest inside. It's made for small stuff, but works very well. Oh yeah. You gotta make your own handle.

Ed

Re: Dang it!

#7

Re: Dang it!

john lucas

>Carole I agree, it's easy to make your own. For vessels your size I would use 5/16 rod. It doesn't chatter as much. I don't even put the HSS on most of mine I just use drill rod to make the tool.

Re: Dang it!

#8

Re: Dang it!

don in central IL

>Could you post a pic so I could see an actual tool. I might be able to make one since I'm having problems with a HF I'm working on. TIA.

Re: Dang it!

#9

Re: Dang it!

Carole Valentine

>Hi Ed,

It's not the minis that I have problems with. I have some homemade tools that work fine on those. This is a bigger piece (for me) and the opening is 3/4". I wanted it smaller, but the micro Keltons just couldn't handle it so I had to enlarge it enough to get the small Keltons in there and maneuver them enough to get up under the shoulder where the grain was so nasty. Still a struggle but I persevered and got it finished.

Thanks all for your replies!