Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

I think I need a coring system

Posts

I think I need a coring system

#1

I think I need a coring system

Jim K in Trappe PA

>This is the mess I made from one bowl this afternoon. Earlier in the day I took a few bags of shavings to the local compost site. I came back and couldn't find my chuck key for my strongold chuck. I had a vague recollection of it falling off the lathe..... Headed back to the composte site, and sure enough, I found it in the pile of shavings I left. I was lucky this time....


img

Re: I think I need a coring system

#2

Nice Lathe Jim :-)

Barbara Gill, Remlik VA

>

Re: I think I need a coring system

#3

Re: I think I need a coring system

merv Graham

>Speaker magnets or hard drive magnets are my method of keeping track of the chuck key. Only takes one trip to buy a new one to reinforce the need. Been der bone dat.

Re: I think I need a coring system

#4

I just bought a bunch of rare earth

Jim K in Trappe PA

>magnets last week. I put one in place as soon as I got the key back today!

Re: I think I need a coring system

#5

Re: I just bought a bunch of rare earth

john lucas

>I have rare earth magnets everywhere on my lathes. The big quarter size ones are great for everything. You can even stick a jacobs chuck to one. I also have them inside my tool box to keep small pins and cutters from getting lost.

A coring system wouldn't help me in this situation. This was from 3 roughly 12 inch rough out's. I am thinking about putting up some roll down curtains to keep the mess a little more confined. I'm also thinking about rotating the lathe so it's more or less parallel to the doors with the backside being on the door side. Then I'll move the tool box out behind me with the grinder on a rolling stand next to it. This will help confine the mess and let me move the toolbox and grinder out of the way when I need to do flat work.

I'm just going to quit mowing the yard and throw the lawn mower out. That will give me more space in the shop and more time to turn. Not sure what my neighbors will think. Thier not woodturners so they probably wouldn't understand.


img

Re: I think I need a coring system

#6

Re: I just bought a bunch of rare earth

Carole Valentine

>John, how are your racks attached to your steel cabinet? I have the same cabinet and would like to do something like that. Did you just use sheet metal screws, bolts or what?

Re: I think I need a coring system

#7

sheet metal screws.

john lucas

>Carole here are some photos of the rack and how it's assembled. It has really been handy but you sorta gotta be a neat freak and put the tools back or it's hard to remember where they go, even though the holes were cut for each tool.


img

Re: I think I need a coring system

#8

detail 

john lucas

>


img

Re: I think I need a coring system

#9

smaller detail 

john lucas

>


img

Re: I think I need a coring system

#10

I also bought a couple clear

Jim K in Trappe PA

>shower curtains. I'm going to hang them up in a way that I can move them out of the way, but pull them open when needed.

Re: I think I need a coring system

#11

Re: I think I need a coring system

robo hippy

>Don't believe what is said about coring systems reducing the amount of curly shavings on the floor and all around the shop. You save so much time by coring that you turn way more, and that means more shavings that ever.

robo hippy

Re: I think I need a coring system

#12

Re: I just bought a bunch of rare earth

Bob Fawcett

>I made a roll up curtain that hangs behind me to stop the shavings. Its just a section of plastic sheeting off a roll I had when I was painting the porch. One end is attached to a 1 x 4 that I screwed to the ceiling joists, and the other end is stapled to a 1 x 1. This just rolls up inside the plastic. I used braided masons line for the cord. Probably took all of 10 minutes to build, and it keeps the shavings contained.

Re: I think I need a coring system

#13

Thanks, John!

Carole Valentine

>

Re: I think I need a coring system

#14

But at least you get a few more

Jim K in Trappe PA

>bowls! Upside, is that too much shavings are better than no shavings!!

Re: I think I need a coring system

#15

Leo Van Der Loo

I strung 2 braided rope lines across the shop,

Leo Van Der Loo

>at 90 degrees, couple of feet away from the lathe and hung shower curtains on them, very easy to slide in place or out of the way, and sure beats cleaning the whole shop up every day.

Have fun and take care

Leo Van Der Loo