Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Vicmarc Chuck Failure

Posts

Vicmarc Chuck Failure

#1

Vicmarc Chuck Failure

Donna Banfield

>Has this ever happened to you?

Last Thursday, I was taking a 17" core out of a maple blank. I was using the Oneway Coring System, the largest knife (rated for taking cores up to 17 1/2") with a brand new cutter. As I got to the very bottom of the core, the entire blank became dislodged. I did not get a catch.

I thought I broke the tenon -- it's happened before. I looked over the blank and saw that the tenon was still intact, and I had clean, solid contact with all points in the large dovetail jaws. My husband was observing, looked over the blank, and said, "You broke your jaws." I didn't believe him. I pulled the knife out of the way, and removed the blank from the jaws, and saw he was right.

Two of the four jaw slides of my Vicmarc 120 had sheared apart. Fortunately, I had a second Vicmar 120 chuck, so was able to complete the work for that day. I checked the Vicmarc website, and didn't see replacement slides as an accessory, so I sent them an email, with two photos attached, inquirng whether it was possible to replace all four jaw slides. That was Saturday or Sunday morning. I haven't heard anything from them.

Up to this point I have been very pleased with this premium chuck, and have no intention of "chucking" it (pun intended), if I don't have to. The chuck and jaw slides are either 2 or 3 years old; I used both chucks frequently, so I have no way of telling which of the two is older. They were both purchased from Craft Supplies.

Anyone have ideas?

And if the photo posted here is poor, or too small, please be patient. I'm really trying to figure out this digital pixel and size thing.


img

Re: Vicmarc Chuck Failure

#2

Re: They don't make them like they used to

Russ Fairfield

>Vicmarc has had a lot of quality problems since Vic Wood sold the company.

Re: Vicmarc Chuck Failure

#3

Re: They don't make them like they used to

adrien

>Wow! That the steel would be weaker than the wood is an incredible quality issue!

Sorry to learn this. I've three Vicmarcs that have stood me in good stead over the years.

Re: Vicmarc Chuck Failure

#4

Re: Vicmarc Chuck Failure

robo hippy

>I have 3 Vicmark chucks. I broke a tooth off of the pinion gear on one, and broke a tooth off the main drive gear on another. I was able to get replacement parts through Craft Supplies. I am surprised that yours broke where it did.

robo hippy

Re: Vicmarc Chuck Failure

#5

Re: Vicmarc Chuck Failure

Greg H. from Wisconsin

>I had the same thing happen to mine. One jaw sheered off during turning a bowl, not coring, there was a catch but nothing I would call "major." Craft Supplies may be willing to help, I'm not sure, my situation they offered, since it was less than thirty days for their satisfaction warranty. I did take the option for the credit and switched back to oneway, I have never heard a problem with oneway's chucks. I don't think Vicmarc's are bad, I just like the fact that Oneway is at least on this side of the dang planet for service and parts, IF NEEDED. That's my two cents

Re: Vicmarc Chuck Failure

#6

Re: Vicmarc Chuck Failure

Rick Allen

>Hi Donna

That is rather impresive. I have the large Vicmark chuck and I would never expect it to give way like that. In fact I wouldn't expect any of my chucks would giveway like that.

Shows you how much force is on those jaws when you are coreing bowls!

I hope you get it all working right again soon. Contact Craft Supplies to see if they can be of any help.

Re: Vicmarc Chuck Failure

#7

Re: They don't make them like they used to

Joe Flemig

>Russ,

Vicmarc is a family-owned business, but it has never been Vic Wood's business. I've met the owner and his name is Vic, but I do not recall the last name. I sort of remember that it is an Italian name.

I also do not think the business has ever been sold outside the founder's family.

Please correct me if I'm wrong.

Joe Fleming - San Diego

Re: Vicmarc Chuck Failure

#8

Russ is right....

TDaniel

>I think.