Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Hollw form -form practice

Posts

Hollw form -form practice

#1

Hollw form -form practice

George Van

>I decided to use roughing as a practice session rather than get it over quickly. I roughed this last night, 6x7 white birch burl, going more slowly, removing frequently, and paying close attention to the upper and lower curves as suggested by Wally. I developed the upper first, removing the bark inclusions. I then established the bottom, shooting for a final finished foot of 2� or less. I then blended the two at the shoulder trying to keep some fullness to the form rather than a more straight line curve. It did not come out exactly as I had sketched; as I had to remove more bark than I thought was present so some plumpness was lost. When dry and finish turned the top will be a natural collar separated from the body by a fillet. I chose not to remove all the bark inclusion as I felt the form would become too narrow, would you agree or would you have removed the inclusion, not knowing how deep it would go?


img

Re: Hollw form -form practice

#2

Re: Hollw form -form practice

John Veerkamp

>George,

I like the natural "defects" like bark inclusions. I think it looks great and provides a focal point. Keep it.

John

Re: Hollw form -form practice

#3

Re: Hollw form -form practice

Ron in Drums PA

>I like the inculsion

Form looks good too!

Re: Hollw form -form practice

#4

Re: Hollw form -form practice

RevDoug

>Looks like you have a great piece going here, George. The wood is tremendous and you have a real nice form going. I'm looking forward to seeing the finished project.

Turn 'em round,

Re: Hollw form -form practice

#5

Paul Porter

If the wood is wet...

Paul Porter

>...the bark inclusion will probably shrink away from the rest of the wood and fall out when it's dry. You can always use coffee grounds and CA to fill any voids around the inclusion.

Re: Hollw form -form practice

#6

Re: Hollw form -form practice

Wally Dickerman in Arizona

>Another possibility....Leave the bark. After the rough-out is dry and you're ready to finish it. Remove the surface bark with a dremel or something similar, and fill it with epoxy and something like turquoise. Don't go too deep with the turquoise. It's stone and it'll give you problems if you want to hollow thin. Also add a little glitter which you can get from a craft store. Adds a little sparkle.

Wally

Re: Hollw form -form practice

#7

Re: Hollw form -form practice

George Van

>Thanks all, Wally help me slow down a little and take more time looking as I turn, taking a little cut at a time. It must be that pace that keeps him so young!

The wood is wet Paul, I will more than likely have to use coffee grounds or a treatment as Wally suggests. I am just about done with the roughing and will get some practice with blanks that are dry now.

Re: Hollw form -form practice

#8

Keith Tompkins

Re: Hollw form -form practice

Keith Tompkins

>HI George,

That piece of wood is spectacular! I've not seen white birch burl before. I'd leave the inclusion, it adds some contrast.

I think you are right; sometimes we are in such a hurry to rough turn a piece, we remove too much wood in the process. I like to look at the roughing process as a way to practice tool control, not just removing lots of wood.

One way to turn a piece that follows your sketch is to make a cut-out of the drawing using a thin, rigid paper. It's easy to stop the lathe, and set the cut-out over the turning to guage your progress. Some turners have a hard time "seeing" the form while it is on the lathe. The cutout method will usually help.

That is going to be a very nice piece!

Re: Hollw form -form practice

#9

Re: Hollw form -form practice

George Van

>Thanks for the idea Keith; I will cut out a template next time, kind of like using training wheels!

This is a nice burl, I have a 24�x8� cap and two 26�x32� � 2 �� platter blanks left to turn. I will have to take these to a friend who has a Oneway 2436. I had three other burls that went to the burn pad; unfortunately they are not all good.


img

Re: Hollw form -form practice

#10

Leo Van Der Loo

Gorgeous piece of burl George

leo Van Der Loo

>No don't take any more wood of the form, it already starts to flatten out like you have seen I think, the bark inclusion should look good, if you think you like to keep it you could let the bark soak full with CA, then it will not shrink much if any, and it is hard to beat mother nature for looks.

How does the birch burl turn George, is it fuzzy like the regular birch or not as bad ???

Hope it will look as good as it seems to promise, than it will be a knockout !!

Have fun and take care

Leo Van Der Loo

Re: Hollw form -form practice

#11

Re: Gorgeous piece of burl George

George Van

>Leo, the burl seems to cut well with a sharp tool and shearing type cut, it does not respond well to scraping.