Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Hook & Loop Informatiom

Posts

Hook & Loop Informatiom

#1

Hook & Loop Informatiom

Bruce in Saint John, N.B. Canada

>To-day I have to order some sandpaper and need some help. In the past I have always purchased 2" & 3" hook & loop discs already cut.

This morning I was searching the web and found a supplier (Industrial Abrasives) that sell sheets (36" X 1 Meter) of Rhynogrip hook & loop sandpaper, various grits. It would be quite a bit more economical for me to purchase it by the sheet and cut my own discs. My quiestion is, has anyone used this particular brand and if so how did it perform? Any help would be appreciated, thanks.

Re: Hook & Loop Informatiom

#2

Re: Hook & Loop Informatiom

W.C. Turner

>I've just recently ordered some, but, haven't used it yet. There's plenty of others that have though, & will chime in.

Check the articles section. Mark Kauder wrote about cutting the sheets up in 2" squares.

Re: Hook & Loop Informatiom

#3

Re: Hook & Loop Informatiom

Mark Kauder, Phenix City, AL

>Industrial Abrasives is well thought of by many around nere. Russ Fairfield turned me on to it.

It may not last as long as some of the fancy purple stuff, but at 1/10th the cost, it works for me for the last 3 years.

If you cut it on the bandsaw like I do, you can get as many as 350 2" squares from one sheet. 4 cents a piece.

Mark

Re: Hook & Loop Informatiom

#4

Re: Hook & Loop Informatiom

Bill Neddow

>The Rhynogrip is really good sandpaper. It does not last as long as some, but it is a lot cheaper -- making it probably the best bargain on the market. I have tried cutting the sandpaper on a band saw as Mark suggested and it works fine. But I still prefer the round disks. These are easy to make. Get a 2" or 3" hole saw. (The cheap ones seem to work as well as the more expensive ones.) Take the centering drill out of the center. Grind the teeth off. Put it in a drill press, turn it on at a medium speed aand start popping the disks out. It only takes seconds per disk. Make sure the sand on the sandpaper is down (not up, as on the band saw).

Re: Hook & Loop Informatiom

#5

Re: Hook & Loop Informatiom

Stuart Johnson

>Works great. I couldn't seem to manage it on my bandsaw so I just use a 4' x 2" steel rule and cut it with a utility knife. If you want you could use a 2" punch to make disks but the squares work just fine.

Re: Hook & Loop Informatiom

#6

Re: Hook & Loop Informatiom

robo hippy

>You can also take a 2 inch, and/or 3 inch inside diameter piece of pipe, ream about 1/16 out of the inside, harden it, put a double bevel on the cutting edge (similar to a skew chisel), and use a 6 lb. hammer with a block of wood on top, and a piece of 1/2 inch plastic for a cutting board. Cut with the abrasive on the down side, and cut 3 to 5 layers at a time. I like mine to be slightly over sized. If you are lucky, you can find a table top punch press, or a large arbor press.

robo hippy

Re: Hook & Loop Informatiom

#7

Re: Hook & Loop Informatiom

Steve Worcester

>Please don't use a sharpened anything in a running drill press to cut sandpaper. The problem is that if (when) the sharpened punch grabs the paper and maybe pulls your hand in with it, it cuts your fingers to the point where you may (will) need skin grafts.

Hit it with a hammer, or a punch or something, don't spin it in a drill. Learn from my own experiences, please.

Steve Worcester

www.turningwood.com