Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Dental Light Question

Posts

Dental Light Question

#1

Dental Light Question

Bill Grumbine (Kutztown PA)

>Greetings all

After many years of lusting after a dental light for the lathe, I have finally acquired one, courtesy of a very kind dentist who is also a woodturner. I installed it temporarily over the Vega bowl lathe to ascertain the range of motion, and it looks real good where it is at, with one small caveat. The post depending from the beam in my roof is just a bit too long. I have been corresponding with my dentist friend, and he does not think it would be a problem to cut some of the post off, but I was wondering if anyone else here had encountered a similar problem - those of you with dental lights, assuming there is anyone else here with one.

Any other tips or experiences would be appreciated as well.

Thanks!

Bill

Re: Dental Light Question

#2

Re: Dental Light Question

Russ Fairfield

>I don't get the picture. How about posting one.

Is this a supporting column the goes all the way to the floor?? Removing that will take some work to distribute the load back to the walls, and the question becaomes on of whether the walls will support the load.

Or, is it just a stub post that extends down below the bottom of the truss or ceiling joist or whatever else is up there running from wall to wall. If it is the later, it may be the remains of an old column that has already been removed, or it may be a member of the roof truss. Either way, cutting it back to flush with the bottom of whatever else is up there will not be a problem.

Re: Dental Light Question

#3

Re: Dental Light Question

Bill Neddow

>I cannot answer your question, Bill, but I have one of my own. I have also lusted after such a light and on my way back from Louisville I stopped at Woodchuckers, in Toronto. Sitting in the middle of the floor was a dental light with a little sign on it saying "free". Needless to say, it was in the back of my truck in a flash. (Must have been a reward for being honest with customs.) Now, I called a dentist friend, who is also a woodturner, to find out where to get a bulb (which turned out to be simple). But he was a little concerned about me putting the light up, claiming it was very "focussed". Does your light spread out a bit, and does it give enough light to be worthwhile? I know they seem very strong when you are on the wrong side of them! I would also be very interested in the answers to you height problem. I have a 10 foot ceiling and will probably have to build a bracket to lower my light.

Looking at mine, it seems the pillar is simply a pipe and it could be shortened if you could get the wires out of the way.

Re: Dental Light Question

#4

Re: Dental Light Question

Bill Grumbine (Kutztown PA)

>Hi guys

Russ, I will try to get a picture later on today. The light has a large bracket that was designed to be bolted to the ceiling. The pipe in question is held into the bracket with set screws. It remains to be seen if they are in a recess, but I don't think they are. I will be finding out later on today on that too. The articulated arm of the light is held to the bottom of the post by set screws in recessed groove, so that it may rotate freely. There is no suport from the floor. It looks like a simple matter of sawing the thing off shorter now that I have looked a little closer at it.

Bill, I have been on the wrong of these lights way too many times - in fact I have another session scheduled for Thursday, and my dentist has a warped sense of humor. This is the last one for a while I hope. But, the light seems to be fairly intense, despite the bulb being tiny. My dentist friend who supplied the light explained to me that they have a working distance, and it will take a little bit of time to get it set for optumum lighting. But as I mentioned to Russ, it looks like the pole can be sawn off short. I will be sure to report with a picture when I get it done.

Bill

Re: Dental Light Question

#5

Check with....

W.C. Turner

>Dave Peeples.

Re: Dental Light Question

#6

Ellis Walentine

Good question, Bill

Ellis Walentine

>I have a dental light that I have yet to hook up. I have conducted some range of motion studies with it, though, because these things are limited in certain axes of travel. I found out that my ceiling is too high to mount the existing pipe to a flange in the ceiling, so I plan to build a wooden brace (sorta like the kind of angle-iron stand you would mount under an external chimney pipe to support it) that will attach to the wall behind my lathe. I will mount a flange on that stand and attach the light mount to the flange.

It's right there on my long list of urgent things to do. :-)

Ellis

Re: Dental Light Question

#7

Dave Peebles has one....

Jennifer@Indy.USA

>

Re: Dental Light Question

#8

Re: A question for the dental .....

JamieDonaldson

>... light users- I have heard that the replacement bulbs are very expensive- what are they and how much do they actually cost as replacements?

Re: Dental Light Question

#9

Re: A question for the dental .....

Bill Neddow

>My dentist friend said the bulbs cost about $20 if you buy the from a lighting specialist -- a LOT more if you buy them from a Dental supply firm. He has several running all day, five days a week, and he says he cannot remember when the last one burned out.

Re: Dental Light Question

#10

Re: A question for the dental ..... *LINK*

Dave Peebles Lyons, Ohio!

>Hi Jamie,

I use a place called bulbworks.com I think the one that I bought was about $12.00. It's been going strong for over two years. The guy I dealt with was great. He sent me a catalog with the prices for the bulbs. I saw that the had three different bulbs for my light. They went from $30.00 to $12.00. When I asked him what the difference was, he told me "About $18.00 bucks " :) I bought the cheapest one on his advice.

Best,

Dave


http://www.bulbworks.com