Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Gluing Ebony or Blackwood?

Posts

Gluing Ebony or Blackwood?

#1

Gluing Ebony or Blackwood?

Carole Valentine

>Will Titebond or CA hold a small cylinder of either of these to a glue block of Oak for turning? I have not tried it because I questioned the strength of the bond, considering the oily nature of the exotics. I would like to use some small pieces that I would not be able to mount any other way.

Re: Gluing Ebony or Blackwood?

#2

Re: Gluing Ebony or Blackwood?

Ian

>carol, i've used ca with no problems.

I usully wipe the ebony with DNA and blow dry with the air line.

then glue as usual.

ian

Re: Gluing Ebony or Blackwood?

#3

Keith Tompkins

Re: Gluing Ebony or Blackwood?

Keith Tompkins

>Hi Carole, Yes, it can be done successfully. I usually don't just butt the pieces together, I form a shoulder on the turning stock, and recess the stock into the waste block. Stronger, and more glue surface.

Re: Gluing Ebony or Blackwood?

#4

Re: Gluing Ebony or Blackwood?

K.S.SONG

>Hi

I have experience bonding the African Blackwood with Tite bond 2.

It failed as a result and you can see the bonding line defects on this photo.

I think that rich oil component of blackwood(more rich than Ebony) may pushed Tite bond out continously.

The Franklin International technical part(Tite bond maker) seems not familiar with the African Blackwood,

and told me "You may also want to check into using an epoxy with the African Blackwood."

I prefer to recommend to use epoxy type.

Enjoy turning

K.S.SONG / Seoul Korea


img

Re: Gluing Ebony or Blackwood?

#5

Re: Gluing Ebony or Blackwood?

Jennifer@Indy.USA

>Carole, this is where the pin jaws come in real handy. That or a collet chuck. I know that doesn't help but just thought I'd toss it out there. I have a set on my old Nova chuck that I can only fit on my Jet Mini...so it becomes the default lathe when I need to make something smallish like that, rather than glue it up. Keith's idea of recessing it into the glue block with a shoulder works well too.

Jen

Re: Gluing Ebony or Blackwood?

#6

Use your morse taper

OB O'Brien

>Carol, I saw Mark St Lugar's demo at the symposium and he had a neat trick for small turnings. He took a knife and trimmed the corners off of a small piece of blackwood, then pounded it into the morse taper of his lathe. It didn't go in more than a little bit, but was still secure enough to turn a finial. Might this work for you?

Re: Gluing Ebony or Blackwood?

#7

Re: Use your morse taper

Carole Valentine

>Wouldn't quite work for what I want, OB, but an idea to be tucked in the arsenal. I am trying to get the small piece away from the chuck and jaws so I can work on it comfortably. It's hard for me to concentrate on turning something extremely small when my hands are so darn close to those chunks of spinning steel.

Re: Gluing Ebony or Blackwood?

#8

Re: Use your morse taper

Leppikallio

>But if you put piece in the morsetaper of the spindle there is no chuck. This is in fact quite good trick.

I have used succesfully ordinary hotmelt glue to hold small & tiny pieces of wood including blackwood. Works well when you allow gluegun to heat long enough and also the glueline cool down long enough.

Also I can suggest these tiny three jaw chucks even they can cause extreme pain if not used properly... really good accessory in smallscale turnings.


img

Re: Gluing Ebony or Blackwood?

#9

Re: Use your morse taper

Carole Valentine

>"But if you put piece in the morsetaper of the spindle there is no chuck."

Duh! OK, so I am not the sharpest tack on the planet. LOL

Re: Gluing Ebony or Blackwood?

#10

Re: Use your morse taper

K.S.SONG

>Hi

Where we can buy this tiny three jaw morse taper chucks which is no need chuck and put in spindle directly?

That is very interesting.

K.S.SONG / SEOUL KOREA

Re: Gluing Ebony or Blackwood?

#11

Keith Tompkins

Re: Use your morse taper

Keith Tompkins

>those tiny machinist's chucks are great....use mine all the time.

Re: Gluing Ebony or Blackwood?

#12

Re: Use your morse taper

Leppikallio

>Penn State has one model for two common spindle sizes:

http://www.pennstateind.com/store/lcm18.html

Mine is from Clisby miniature lathe and morse arbor with 1/2" x 20 tpi thread was from some machine shop.

Re: Gluing Ebony or Blackwood?

#13

Re: Thanks. Enjoy turning!

K.S.SONG

>