We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
>Has anyone found a slick way to mount the threaded ends of the Beall balls to a flex shaft or air powered die grinder? I was thinking of hunting down a machinist willing to make something with the nesessary female thread and a 1/4" shank. I am trying to buff deep inside a irregular surfaced carved wood vessel.
>Dayle I haven't done that but I did turn some adaptors for my tubular sanding drums so I could use them in my flex shaft. I had to turn the big ones out of solid steel but the smaller ones I made using all-thread couplers. I found a coupler with the right size thread and then bought a bolt to fit the other side. I cut the head off after screwing it in the coupler. I drilled through the coupler and bolt the same size as a nail that I had and drove it in to lock the bolt in place. Then I turned this down to 1/4". The same thing would work for the beal buffs but I don't remember the thread size. Probably somewhere around 5/16 I think.
You might try looking in the Rio Grande catalog. They have all sorts of buffs that fit flex shafts.
I have a bunch of Dremel buffs I use for really small stuff and for reaching into really tight recesses where the Beal won't go.
>I have a flex shaft which is powered by a drill. The flex shaft has a 1/4" Jacobs chuck at the business end. I just put the ball buffs in the chuck. I don't care if I mangle the threads because I only use the buffs in the flex shaft.
>Woodworks supply has a heavy duty one that fits in a drill. One of my friends had an adaptor made so he could connect it directly to a 1725 rpm motor shaft. That's his main carving tool.
>Home Depot and many other places. It is a Delta branded product which is designed to attache to some of their small benchtop belt/disc sanders.
These are not meant for high speed or extended time use. It often sells for about $30.
This is a poor subsitute for a Foredom but it is also cheap enough that being wrong won't hurt to much. And you are very likley going to get $30 worth of use out of it anyway.
>Yup. I got a flex shaft like the one shown. The problem with it is the chuck is to small to mount the threaded shaft on the ball. I didn't measure it but the OD appears to be about 3/8". I'm toying with the idea of sanding the shaft down freehand but I know till I'm done the things going to have a pretty bad wobble and the ball would be toast. I like the idea of messing around with threaded couplings though. Since I don't own a metal lathe, I suppose I could chuck up a short piece of all thread on my drill press abrate it down to a 1/4" reasonably accurately then I could turn it into the coupling and mount the whole thing in a 1/4" collet.
>That's something to check out,the one I have is 1/4". But really from my experience that kind of flex shaft heats up real quick under any kind of laterial heavy load, maybe the 3/8" one is a bit more robust. It would really be my #3 choice for trying to run the ball.
>what you ask for, but something similar for the same end.
I mounted a right angle air die-grinder on the end of a 20" pipe nipple with a elbow on the other end and a ball valve > quick-connect air line. I taped the air trigger down, and use the little sanding disk that came with the 2" arbortech head on the air-grinder. This disk came with a cloth abrasive glued to it, I pulled that off, scuffed the plastic face then sprayed it with high tack contact cement. I can punch out my own disk to about any size from the gold peel and stick. and they stay on and last longer than I had expected.
When I use this, I hold it loosly with my left hand near the rim, and my right hand on the valve which is at a right angle to the length, which gives good direction control on the other end.
If you had trouble following this, I can post a photo if anyone needs it, or send me an email for more photos. Although, I really should write an article if nobody else knows or uses this, and if there is enough interest.