Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Pneumatic Air Hammer Choices

Posts

Pneumatic Air Hammer Choices

#1

Pneumatic Air Hammer Choices

Chris Andrew

>I'm thinking about getting a pneumatic air hammer to do some texturing. I'm specifically interested in the single-bit air hammer as opposed to a needle scaler. A trip to some of the local suppliers resulted in questions regarding the specs that work best for this. I assume a short stroke (1 5/8) and high BPM (5000) would be preferable. Models with these specs also seem to require less CFM from the compressor. Are my assumptions correct? Does anyone have advice about these that might help me get the right unit for this purpose?

Re: Pneumatic Air Hammer Choices

#2

Re: Pneumatic Air Hammer Choices

Bob Fawcett

>Chris,

I have never tried to use a single bit air hammer for texturing, although I own 2 of them. I used to be an auto mechanic and have a large Snap-on and a smaller no name hammer. I don't think either one would be suitable for texturing. They both hit to hard. I used the snap-on the other day to knock a hole in my poured concrete wall for the pool wiring to go through (faster than a hammer drill). The smaller hammer maybe, but I don't think it would give the kind of result you want. What type bit could you use?

Re: Pneumatic Air Hammer Choices

#3

Re: Pneumatic Air Hammer Choices

Chris Andrew

>Bob,

Grame Priddle from New Zealand uses a pneumatic air hammer to texture his turnings. The bit used is a round-nosed punch (I don't know the correct name for it). Needle scalers have also received much attention lately as texturing tools.

Re: Pneumatic Air Hammer Choices

#4

Re: Pneumatic Air Hammer Choices

John Lucas

>Chris I use a dremel engraver. I remove the pointed tip and replace it with a rounded over bit, it's 1/8" so i just used an old drill bit shank. I used to freehand draw patterns probably in the same way Greame uses his tool. You can get them for around $19.

Re: Pneumatic Air Hammer Choices

#5

Dremel Engraver

Chris Andrew

>John,

I never thought of that -- what an excellent idea! I assume you've seen Greame's work...does the texturing from the Dremel look/feel similar? Do you have a photo of your work with the Dremel texturing?

Re: Pneumatic Air Hammer Choices

#6

Re: Dremel Engraver

Lan Brady

>You have several great options. You noted the most important yourself. Match the air flow of the hammer to your compressor.

You can adjust the air pressure way down to get the softer dimples.

You will need to shape/round the chisel points. They were not meant for wood. But we all make minor adjustments, don't we!

I use a cheap model from Harbor Freight, it does not take much power to work on wood. Also they sell a needle scaler attachment for less than 15 dollars. Now you have both for less than 40 dollars

Good Luck, Lan

Re: Pneumatic Air Hammer Choices

#7

Re: Pneumatic Air Hammer Choices

RobinCorell

>An old friend of mine who also dabbled in stone carving had the cutest little air chisel. I used to alsways tell her if it ever went missin to come look in my tool box. Not that I ever had any need for it.

Not sure who it was made by but it was one of those inline tools, similar to a neddle scaler. it was about 8" long and only 1 1/2" in diameter and fitted with a valve to contriol to pressure/force of the stroke.

I have a sculptors tool catalog that has a bunch of stone tools in it. If I can find it I will take a look see.

Robin

Re: Pneumatic Air Hammer Choices

#8

Re: Dremel Engraver

John Lucas

>Chris I'll look to see if I have any of the photos of pieces I've done. If not I'll just do a sample and shoot it tonight to show you. It's sooo easy.

Re: Pneumatic Air Hammer Choices

#9

Re: Pneumatic Air Hammer Choices

Bob Fawcett

>It just occured I also have a pneumatic gasket scraper. This is a very small air hammer used to drive a wide chisel to scrape gasket material from engine parts. This could also be adapted to texturing. It is smaller than most air hammers and low powered.

Re: Pneumatic Air Hammer Choices

#10

Trow & Holden...

Peter Teubel

>They are a stone carving tool supplier. The cheapest pneumatic chisel they sell is $245. Al Stirt uses one to carve flutes in his bowls. He adapted Arbortech power chisels to a shank that fits the air chisel socket. Short stroke and variable valve provides very precise control.

Re: Pneumatic Air Hammer Choices

#11

Bob Moffett

Re: Trow & Holden...

Bob Moffett

>I attended a workshop by Al Stirt and he recommended the "Bare Short Stroke Pneumatic Carving Tool: Type "B" in both the 3/4" size and Bantom size. I took that out of his handout. It comes from Trow & Holden phone # 1-800-451-4349. I have no affiliation with this company.

Re: Pneumatic Air Hammer Choices

#12

Dremel engraver texture

john lucas

>chris Here is a sample of the texture. Of course it depends entirely on how you scribble. You can even do it with the lathe spinning. It's really awsome how many different textures you can get with this thing.


img

Re: Pneumatic Air Hammer Choices

#13

Re: Dremel engraver texture

Chris Andrew

>John,

This is great. I'm going to give it a try. Any tips on shape when rounding off the drill bit?

Chris

Re: Pneumatic Air Hammer Choices

#14

Re: Dremel engraver texture

john lucas

>Chris I just broke the drill bit where the shank meets the flutes. Then I chuck it up in a drill and while it was rotating ran a file and then sandpaper over it. I don't think it has to be perfect just rounded and smooth.