Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

DIRTY ONEWAY HELP!

Posts

DIRTY ONEWAY HELP!

#1

DIRTY ONEWAY HELP!

Bill Hale / Woodspinner

>I look at all the pics of the nice clean lathes you all and have come to the conclusion that I must be a slob. OR,is there a way to get it clean and repaint ?

Oneway 2436 with lots of CA and finish on the banjo and body.

Thoughts and knowledge will be appreciated.

Bill in Casa Grande, AZ.

AH - going back to CO. on Thur


img

Re: DIRTY ONEWAY HELP!

#2

Hey...

Peter Teubel

>Mine is only clean because its got maybe a couple hours on it. Don't worry, I'll get to your level of "patina" soon! Personally, I think that color would be very hard to keep clean with a lathe that's actually USED alot.

Re: DIRTY ONEWAY HELP!

#3

looks clean to me

e

>the white is just a 'canvas' that allows you to color your lathe with any tone you want ...

mine is more of a reddish tone these days...

remember, after a certain serial number the lathes were powder-coated. i have an earlier one that i can't use any solvent-based cleaners on.

Re: DIRTY ONEWAY HELP!

#4

Paul Porter

Re: DIRTY ONEWAY HELP!

Paul Porter

>Dirty! Wadoyoumean dirty! It looks normal to me.

Re: DIRTY ONEWAY HELP!

#5

Re: DIRTY ONEWAY HELP!

robo hippy

>Dirty????? Compared to my PM, yours is almost virgin clean.

robo hippy

Re: DIRTY ONEWAY HELP!

#6

Re: DIRTY ONEWAY HELP!

Norm Smith

>Bill, We are not slobs. I have a Powermatic that is full of crap. I use it almost every day so it has to get dirty. Someday maybe I will clean it up and put a coat of paint on it but not for a very long time.

Have fun and get it dirty is the way I look at it.

Norm

Re: DIRTY ONEWAY HELP!

#7

Re: If you had bought a nice....

JamieDonaldson

>...flat black Stubby you wouldn't have such unsightly problems!!! :))))

Re: DIRTY ONEWAY HELP!

#8

Do Not Use CA Softener

Barbara Gill, Remlik VA

>It will take the paint off.

Re: DIRTY ONEWAY HELP!

#9

Re: DIRTY ONEWAY HELP!

Fog Tanner

>When I got my Delta, I put two coats of car wax on the whole thing, the bed and all the painted surfaces. When I got my Vic 300, same thing, I waxed everthing that I could reach. That got rid of the problem you have encountered. I was given that tip by someone who had the same problem as you - same lathe.

Since you will have to strip and repaint, you might think about some of the "Grafitti Paint". I was looking for some new paints for my raceplane and came across a paint made for school buses. Our raceplanes always had a stream of oil going down the side of the plane from the 2 cycle fuel (oil, nitro, and methonal). This paint was impervious to the oil. You can spray it with any other paint and it will either run off or you can wipe it off with a rag - the grafitti that is. Basicly no paint will stick to it, the only problem is it will not adhere to itself so there is no such thing as a minor touchup. Not sure of the color choice, as I didn't go anyfarther since there is always that ding on landings.

You can always repaint your lathe with one of the automotive paints, I use Deltron and use a clear like Deltron Clear which is impervious to your normal finishes. Alcohol will not phase it, I use 95% to clean the plane up - and nitromethane will not strip it. You can also get some pretty cool colors, just depends on your pocket book.....

Re: DIRTY ONEWAY HELP!

#10

Re: DIRTY ONEWAY HELP!

Eddie Pacheco, San Jose, Ca.

>Oneway switched to Powder Coating a while back so removing the paint will be no trivial matter if you lathe has this treatment. You're talking muncho $$$ to then get it recoated. I would suggest automotive "polishing compound" on a small area to see if you get any results. If this works then try the "rubbing compound" (coarser grit) to removes the surface stains, follow this with the "polishing compound" to get the luster back. Then you can use either a 3M or Mirror Glaze final finishing product to get a brighter finish. Wax after all of this and your done.

On the other hand, that "dirty lathe" would look real nice in my garage....:-)

Re: DIRTY ONEWAY HELP!

#11

As a friend and finishing guru used to say...

Peter Teubel

>"Never underestimate the power of BLACK PAINT!"

Re: DIRTY ONEWAY HELP!

#12

Re: DIRTY ONEWAY HELP!

eaglesc

>I have often thought it would be neat to have a "nastiest looking lathe contest"

The winner would receive a gallon of acetone to clean it off.