Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Platter and Glue Block?

Posts

Platter and Glue Block?

#1

Platter and Glue Block?

George Van in WI

>I just roughed this thin 16�x2� blank from a stump I am cutting up. I am going to put a glue block on it, as I hate to waste any of the height with a tenon. I had to rough between centers for alignment because the surfaces were too irregular for a screw chuck. I am going to use thick CA glue on a 5� block. How long do I have to wait till I can rough out the interior?


img

Re: Platter and Glue Block?

#2

Re: Platter and Glue Block?

Carole Valentine

>Sure is a pretty piece of wood! Can't help you with the time for CA though...I don't trust the shear strength of CA and always use Titebond which I clamp and let sit over night. Just a chicken I guess. :)

Re: Platter and Glue Block?

#3

Richard Allen

Re: Platter and Glue Block?

Richard Allen

>If you use the tailstock for support, you can start right away.

By the time the tailstock is in the way the glue will be fully cured. BTW I would use medium.

Also be careful about CA glue flying into your eyes. Stay out of the line of fire and safety glasses of a face shield would be a good idea. You can turn the lathe on and then off to see if any of the glue is being forced out of the joint when you start up the lathe.

Good Luck

Re: Platter and Glue Block?

#4

Re: Platter and Glue Block?

Ron in Drums PA

>I use med CA and apply pressure from the tail stock as a clamp. I then sharpen my tools and once I'm finished then I ready to turn. I've cored bowls this quick and so far did not have any problems.

I don't use accelerator.

Thick CA is slower to cure.

Re: Platter and Glue Block?

#5

Re: Platter and Glue Block?

Russell L. Babbitt Jr.

>Nope, no CA for me. I would use yellow glue of some kin and sit overnight. Even with yellow glue I would use the tailstock for security until I need to remove it to finish the piece.

Re: Platter and Glue Block?

#6

If it is green wood -----

Jake Niedling

>From your message, I am assuming it is still green wood. I am not sure how well yellow type glues work on wet wood. I would use CA glue and then use the tail stock center for as much of the turning as possible. When you need to clean up the center, pull the tail stock back out of the way. Is your plan to rough out the platter and re-turn it after it dries or complete it at this time?

Re: Platter and Glue Block?

#7

Re: Platter and Glue Block?

George Van in WI

>Thanks all for the advice. I will use medium CA glue since it is not dry wood, I had it spalting for two years, but with yellow birch, the bark retains the moisture. I will follow the advice and give it a little time before starting to turn and use the tailstock for as long as possible. I will rough the blank, then set it aside to dry, starting in a cool place for a couple of weeks. Stump yielded 6, 15�-18� bowls, which I will core, this platter and some good hollow form pieces. I look forward to final turning after drying!

Re: Platter and Glue Block?

#8

Re: Platter and Glue Block?

theeyres

>I must admit, I'm surprised by the number of people who are afraid that CA will fail. Have you had that happen? The only time I've ever had it fail is when I didn't have two perfectly flat surfaces and I tried to get away with it. Even then, more than once I've been able to squirt a little Thick into the crack, hit it with dryer and it's become as hard as a rock.

I'd use CA for this purpose.

Earl

Re: Platter and Glue Block?

#9

Re: Platter and Glue Block?

eliot

>Caroline is so right! I've had several failures, and got hurt once, because a CA glue block failed. I agree with Carol to glue with yellow glue and wait overnight. If you insist on using CA, use thick on one one face and thick on the other, make sure the surfaces are really flat, DON'T use accelerator, and wait about 15 minutes. And wear a face shield.

Re: Platter and Glue Block?

#10

Re: Platter and Glue Block?

eliot

>I meant to say , thick on one face and THIN on the other.

Re: Platter and Glue Block?

#11

Re: Platter and Glue Block?

George Van in WI

>I used the CA and as the neighbors stopped and hauled us out to dinner it is still in the shop. It must be dry by now. since the blank was wet I was afraid of the yellow glue.

Re: Platter and Glue Block?

#12

Re: Platter and Glue Block?

tek-Brunswick, Ohio

>I'd just use a recess instead of a tenon. I'd use my #3 jaws on the talon chuck and make a recess about 1/8" to 3/16" deep. As long as you don't get a giant catch, it works fine. The recess gets incorporated into the foot of the platter as the last step. If I used a glue block I'd use yellow glue and mount the block on a screw chuck.

Tom

Re: Platter and Glue Block?

#13

Re: Platter and Glue Block?

Wayne Leach-NW Ontario

>How come nobody has mentioned 5 minute epoxy? Is this a no-no?

I have used it several times with success!!!

Wayne

Re: Platter and Glue Block?

#14

Re: Platter and Glue Block?

Allen Neighbors

>When the wood is green/wet, I use Gorilla Glue, and let it set overnight. Never a failure, if you don't squeeze all the glue out when clamping.

Allen

Re: Platter and Glue Block?

#15

Re: Platter and Glue Block?

Wally Dickerman in Arizona

>George, I've been using glue blocks for most of my turnings for over 20 years. Many, many hundreds of pieces. Properly used, CA glue will do the job. There is no curing time. Apply the glue, med. CA, wait 30 seconds, use accelerator, and the piece can be mounted on the lathe immediately.

There are really only 2 reasons for a glue block failure. You are making a glue joint, so both surfaces must be flat and true, and the wood must be solid. The most common reason for a failure when using CA glue, is not using enough glue. No clamps, just firm hand pressure for a few seconds. If there isn't squeeze-out all around you haven't used enough glue. Give the excess glue a shot of accelerator to avoid a face full of glue when you turn on the lathe.

Wally

Re: Platter and Glue Block?

#16

Re: How I do it !

Bill Hale / Woodspinner

>Hi George

I have attached a sketch of how I do all of my pieces.

No wasted time on a glue block. I start between centers cut the tennon and the base at the same time. I continue the rough out of the outside.

Actual thickness loss may be no more than 3/8 in.

Good turning and be safe

Bill in Casa Grande, AZ.

Re: Platter and Glue Block?

#17

Re: How I do it !

Bill Hale / Woodspinner

>Forgot sketch


img

Re: Platter and Glue Block?

#18

Re: Platter and Glue Block?

George Van in WI

>Thanks again everyone, the aspen glue block, 5�, worked fine with the med CA, alignment was good and the glue block is solid, cutting was normal. I will be glad to add this method to my mounting options when there is no wood to waste for a tenon or recess.

Bill, I will give your method a try on my next platter.