Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

deep hollowing problem

Posts

deep hollowing problem

#1

deep hollowing problem

ken chase

>Somehow I missed the predrilled hole and fighting with the stub at the center of the hollowform. It's 12" deep. Is there a trick to remove this material? Also would appreciate suggestions of the best way to drill a 12" deep hole about 1" in diameter so I won't repeat.

Thanks

Re: deep hollowing problem

#2

Re: deep hollowing problem

Carole Valentine

>Ken, I can get to them with the curved Kelton. I turn the tool so the tip is angled to about 8:00am and start shaving very lightly with the top edge of the tool across the nub, right to left, down to up, repeat. Just barely take a hair of shaving though or you will just get thrown off the nub and can dp nasty things to the neck of the vessel. DAMHIKT. And don't get that tip on the nub. The other option if the opening is big enough, is a round nose scraper. Just my two cents which t'aint worth much. Would like to see some of your work. You haven't posted any in a long time.

Re: deep hollowing problem

#3

Re: deep hollowing problem

ken chase

>Thanks Carol:

I just finished my first carved piece done totally off the lathe.

I'll post it today.

Re: deep hollowing problem

#4

Re: deep hollowing problem

ken chase

>no luck. In photoshop I made the photo 4"X3" and saved constrained for web. It still read more than the allowed 80K and I don't know what more to do. So I won't be posting.

Re: deep hollowing problem

#5

Re: deep hollowing problem

eliot

>I have a weird way of getting rid of a troublesome nub at the center. (I'm not sure if this is what Caroline is referring to.) What I do is to use a curved Jordan tool( so the tip points to the left) -- BUT I turn the lathe IN REVERSE and approach from the right side of the nub. Otherwise, I find,as Caroline apparently has, that the tool can spin violently counter -clockwise and bash the heavy tool, near the handle, against the rim of the vessel, where if usually breaks.

Re: deep hollowing problem

#6

Re: deep hollowing problem

ken chase

>Doesn't sound wierd at all. Thanks I'll give it a try. Scraper bit?

Re: deep hollowing problem

#7

Re: deep hollowing problem

Bob Fawcett

>Change the size measurement to pixels and resize so both dimensions are less than 480 pixels. This should do it. If not change the jpeg setting to lower quality, or resize a little smaller.

Re: deep hollowing problem

#8

Re: deep hollowing problem

eliot

>Yes, it's one of those little boat -shaped scraper bits borrowed from the metal lathe world. John Jordan Dennis Stewart, etc.

Re: deep hollowing problem

#9

Re: deep hollowing problem

Walter Ahlgrim

>This is my long bit. I made the extinction from scrap the shaft is part of an old bent foes ball rod, the shank that chuck closes on is part of an old tie wall nail. I ground the bar square and bur free it fit throw my chuck and seated in the Morris taper and my small jaws clamped the bar ran very true. Since my bar is hollow it made for easy drilling. Cross drilled for four #4 nails and peen them over. I only use this bit after the hole has been started a few inches with another bit.


img

Re: deep hollowing problem

#10

What kind of bits do you have?

Phil Joines Krum, Texas

>Most bits can be fitted with an extension. I wouldn't use a spade they vibrate.

The 1� Silver $ Deming bits with a 1/2� shank work well. An extension can be made using some 1/2� drill rod and a motor shaft coupler. The 1/2" entension tends to run straiter.

This is what I use but I make them 18" long. You need a 1/2" capacity drill chuck to use it.

Enco part #�s

17/32 to 1� 5 bit set, $11.35 301-0205 (cheaper than just the 1� at most places)

1/2� ID 1�OD shaft coupler, $6.45 891-6317 (you can turn the outside down on the lathe or grinder for more clearance if you want)

1/2� x 3� drill rod, O1, $6.18 408-0029 (use the extra to make some tools)

Or you can get a 1"x 12" Aircraft drill for about $100

Re: deep hollowing problem

#11

Re: deep hollowing problem

robo hippy

>To remove the center cone that you can get, the cutter also has to be at exact center height. If you are cutting above center, the cone will get larger. This is similar to getting down to the bottom of a bowl, and that last little bit at the center that always wants to tear out. If you are doing it free hand, and not in a captured system, Dave Elsworth showed how to it do on one of his videos by using very slight sweeping cuts across, and up and down. This helps you 'find' the cone by feel and touch, and cut it out. Practice on something that you can see first to get the feel of it. To get a measure of dead center, I move the cutter up to where I will be cutting (while outside the form), and use a tape measure to get exact height. I found on my PM that this height is 10 3/16 inch.

robo hippy

Re: deep hollowing problem

#12

Re: deep hollowing problem

ken chase

>Walter : Thanks much for sharing. Looks great!

Re: deep hollowing problem

#13

Re: What kind of bits do you have?

ken chase

>Phil:

Thanks for the great information.I'm am most grateful