Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

PM352A

Posts

PM352A

#1

PM352A

W.C. Turner

>I intended to post this on georgetroy's 3520A message board, but after way too many tries, I gave up. Unlike, most others, I registered with no problem. Now, though, it will not accept my password. I even changed it, & it still won't work!

I've been unhappy with the toolrest that came with the 3520, & would like to replace it.

1) Has anybody else done this?

2)) What did you replace it with?

3) Does anybody have a link for the General website(that makes lathes, etc. in Canada), and the Woodfast website?? I want to see if they have a rest with a 1" toolrest post for the 3520A? Anybody know?

4) Y'all got any replacement recommendations?

Thanks,

W.C.

Email: Remove2

Re: PM352A

#2

Re: PM3520 Toolrest

Allen Neighbors

>WC, I recommend Oneway. They have toolrests with 1" posts you can order for any lathe.

Bill Grumbine also had a post on this forum about toolrests... I forget the name of them, but you can search for toolrest or toolrests in the last 6 months and find it.

HTH,

Allen

Re: PM352A

#3

Re: PM352A

Dennis Y

>I have some from Bestwood. Round and strong. Available from Brad Packard or direct from them. Dennis

Re: PM352A

#4

Re: PM352A

john lucas

>I've got 2 from Bestwood tools and the 6 " and 14" from powermatic. I'm not super please with any of them althought they all work well, I'm just too picky. I'm going to try to make my own this summer when I get the forge fired up. I have some ideas but haven't had time to implement them. I like my Bestwood toolrest but sometimes it's too far from the work since the tool rest banjo is fairly wide on this lathe. It's been good on bowls, it's platters that give me the problem.

Re: PM352A

#5

Re: PM352A *LINK*

Russell L. Babbitt Jr.

>General International

Hope this is what you were after.


General International

Re: PM352A

#6

Re: PM352A

Norm Smith

>I bought a 6" rest from Oneway and it works great on my PM.

Norm

Re: PM352A

#7

Re: PM352A

Doug Thompson near Cleveland

>WC, make your own. Start with 1" cold rolled steel, cut the post 7 inches long then make the rest whatever shape you need. A welding shop could help if needed. I did notice that working more than 7 inches away from the post the rest starts to vibrate... because the banjo clamp can't take the stress. I plan to make a heavy duty banjo so I could use a 11" rest. "The cat in the hat" is a huge turning.

Below is a few examples... they ain't pretty but they work great.


img

Re: PM352A

#8

Re: PM352A

eliot

>What is it about the tool rest that you don't like? I have both the smaller and larger ones and haven't experienced any problems.(Well, there is a small hump at the center that sometimes gets in the way if your angling the tool way up. But I manage all right.)

Re: PM352A

#9

Re: PM352A

robo hippy

>I got the inside and outside curved tool rests from Oneway before they changed them and made the posts shorter and now they won't work in the PM. I like them the best for the bowls. I had 6, 9, and 12 inch rests made from round cold rolled steel for other rests, and like them also. I would like to have a 24 inch long one for turning table legs.

robo hippy

Re: PM352A

#10

Eliot...

W.C. Turner

>To me, there seems to be too much offset of the post in relation to the rest.

Re: PM352A

#11

Doug

W.C. Turner

>Your rests look really good!

Re: PM352A

#12

Thanks, very much.....

W.C. Turner

>to all that replied!!

Re: PM352A

#13

Re: Eliot...

eliot

>Just went into the shop to look at the 6 inch and the 14 inch. I see what you mean, but I can't agree. I certainly don't want to make a big deal out of it, but the offsets appear to have been engineered that way for good purpose: they allow you to get the rests fairly close to small diameter work while keeping the banjo footprint entirely on the lathe bed ways.