Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Oil finish, Beall system

Posts

Oil finish, Beall system

#1

Oil finish, Beall system

Dennis Thomas

>I have finished several bowls (ash, walnut), using a walnut based oil finish. I apply three coats of oil, waiting 24 hours between coats, then wait 3 days before using the Beall system.

I have noticed that the heat of buffing brings a small amount of oil to the surface, which I wipe off between continuing. (I apply the tripoli and white diamond at about 800 RPM and the carauba at about 400 RPM). After the wax is applied and the bowl is room temperature, there isn't any feeling of oil.

My questions are:

1. Is this normal?

2. Or should I wait longer between steps and before buffing? How long?

Thanks

Dennis

Re: Oil finish, Beall system

#2

Ric Taylor

Re: Oil finish, Beall system

Ric Taylor

>Dennis,

I buff between coats of oil. Although it isn't required, and it is more work, it might make a difference. Make sure that when you apply the oil, wipe it off until it is really completely dry.

Also, I wouldn't use the white diamond on walnut, or any other dark, porous wood. You will see white specks left in the pores of the wood that can't be removed.

Ric

Re: Oil finish, Beall system

#3

Re: Oil finish, Beall system

eliot

>I used the Beal buffing system on a cedar bowl; and it was extremely smooth but not impressive; I wanted more gloss. Just for laughs, I applied Russ Fairfield's three part brew to it with a little circular French polish technique, and WOW! Just try it.

Re: Oil finish, Beall system

#4

Re: Oil finish, Beall system

Carole Valentine

>Your oil has not cured. I wait a minimum of 7 days before buffing and more if humidity is high, and that's using Waterlox which cures fairly quickly. It's been my experience that Walnut oil finishes take much longer to cure than other finishes.

Why do you buff at such a low speed?

Re: Oil finish, Beall system

#5

Re: Oil finish, Beall system

Dennis Thomas

>Carol,

I use the lowest speed on the lathe to apply the wax. I've assumed (maybe wrong) that it would keep the heat out of the process and didn't think higher speeds would make it better.

What speeds to you use for applying the wax?

Thanks

Dennis

Re: Oil finish, Beall system

#6

Higher speed on Carnuaba stick

John Lucas

>I do the opposite. I feel like the Carnuaba wax is harder to melt so I use a higher speed on it than I do with the other two. Anyone else have any thoughts on that? I don't have any proof that it works any better than slow speed it just seems to charge the wheel better at higher speeds than the white diamond so I assumed it had to have more heat to melt the wax.

Re: Oil finish, Beall system

#7

Re: Higher speed on Carnuaba stick

Barbara Gill, Remlik VA

>I agree. I always use a high speed with the wax. The higher the speed, the firmer the buff also. I use a high speed for all the buffing unless the surface is irregular (green burl turned to finished).

I also found out that if the wood soaks up a lot of oil do not buff too early. The oil may apper dry, feel dry, and even buff as if it is dry but the surface is getting sealed and the solvent down in the wood will take forever to evaporate. DAMHIKT

Re: Oil finish, Beall system

#8

Re: Oil finish, Beall system

Mike Cunningham (Cape May)

>Try 1900 RPM for all 3 buffs and use a fair amount of pressure against the buff, enough that it's deflecting. Use the various compounds sparingly. I use Watco and have never observed it coming to the surface during buffing or at any other time.

Re: Oil finish, Beall system

#9

Re: Higher speed on Carnuaba stick

Carole Valentine

>Yep. What they said. I buff at 1800 or higher for all three compounds. Carnauba wax is a very hard wax with a higher melt temp than other waxes. It needs the heat to apply properly. Most important thing is to be sure your oil has cured completely.

Re: Oil finish, Beall system

#10

Re: Oil finish, Beall system

Dennis Thomas

>Thanks to everyone for replying and the good info.

In my next batch of bowls, I will:

1. Increase the speed (1800)

2. Wait longer before buffing.

Thanks

Dennis

Re: Oil finish, Beall system

#11

Re: Oil finish, Beall system

Russell L. Babbitt Jr.

>Beall recommends 1725 for their wood buffs and a higher speed for their bowl buffs. I use the 1725 rpm motor removed from my Delta 14" band saw for all buffing. If I ever get a inexpensive 3250 rpm motor I may use that for my bowl buffs.

I use the 1725 for all compounds.