Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Lathe height questions

Posts

Lathe height questions

#1

Lathe height questions

Allen Neighbors

>I am 5'10" tall. My present lathe spindle height is 47". It seems too low to me, since I seem to be bent over too much of the time.

First question is this: What is the reason for keeping the lathe spindle at or near elbow height?

My second question: What problems would I encounter if I place my new lathe spindle height at 49"?

Thanks for responding.

Allen

It shipped today... should have it in 2-4 days. :o)

Re: Lathe height questions

#2

Re: Lathe height questions

Jim Pugh, Ohio

>Allen, your new height, 49" might make it more comfortable if you are doing bowls/hollow forms and less comfortable if you are doing much detailed spindle work. A piece of 2x6 will raise your lathe 1.5" and can be readily removed if you don't care for the height. Go for it.

Re: Lathe height questions

#3

Steven Antonucci

It depends on what you turn

steve antonucci

>Lower is better for hollowforms, but not so great for spindles...

When I was turning at Ellsworth's workshop, I was one of the tallest guys on the lowest lathe. At first, I felt constrained, but now I wish I could lower my spindle height on my Nova about 1.5" (I know I can build a platform...) There is no "right answer" to your question, only what people are used to...

It would be awesome if they made lathes that were easily and quickly adjustable by 2-4 inches...

Steve

Re: Lathe height questions

#4

Re: It depends on what you turn

don in central illinois

>They are, they're called 2 x 4's.

Re: Lathe height questions

#5

Re: It depends on what you turn

John Lucas

>Steve I think the stand that John Jordan sells with the Stubby is adjustable but I don't know how easy it is to adjust. The lathe is quite heavy. Of course you could always buy one of the hydraulic Scissor lift stands that they sell at industrial supply houses. then you could have any height you wanted in just a few seconds.

Maybe we could start a custom lathe fitting business kind of like the Fit Kit they have at Bike shops. You could rent our lifts and use them for a few months until you find the exact height and them we would build a custom stand just for YOU.

Re: Lathe height questions

#6

Re: It depends on what you turn

georgetroy

>Steve the Robust lathe has that adjustment of 2-4" in the legs. I know because I have one. How sweet it is to be able to move a headstock to the end of the lathe. I just don't like a high spindle height where I have to bear the weight of the tools and my arms. In my opinion the spindle adjustment should be where you can bring your body to bear, not with your arms flapping in the breeze. GT

Re: Lathe height questions

#7

Re: Lathe height questions

Bob Fawcett

>Allen,

My spindle height is 46" and I am a little shorter than you. this was as low as I could get the Powermatic. I built a platform because I like it a little lower. The platform is about 1.2" and I have some foam mats on top of that that are about 1/2" thick. This puts the spindle right at my elbow.

Go to Walmart and look in the section that has the excercise equipment and find the interlocking foam mats.

Check your glasses and make sure you aren't bending over to see.

I found my hydralic floor jack for the car is perfect for lifting one end of the lathe to make adjustments.

I know you can hardly wait the next few days. Stop worrying and have fun.

Re: Lathe height questions

#8

Re: Lathe height questions

Wally Dickerman in Arizona

>For bowl turning and especially for hollow form turning, at 5'10", 49 or 50 inches would be about right. For hollow forms perhaps even a bit higher.

My Nichols lathe has a height adjustment of about 4 inches. Most of my turning is hollow forms. My lathe is adjusted so that when using my hollowing tool I can can stand comfortably upright. I have a potential back problem so I want the lathe to be just right for me.

Wally

Re: Lathe height questions

#9

Steven Antonucci

OT:I've been fitted for a bike before

steve antonucci

>58.5CM...

I'm always amazed at the number of people I see 'squirrelling' along (zigzagging back and forth because they can't ride a single line) on bikes that are so poorly fitted they shouldn't even be allowed on the road. I worked in a bike shop years ago, and more than once, I had people ask me a for a "big bike"- 25" frames for a guy 5'4". "I like big bikes..." was always the reason, even though we could have saved him two pounds by sawing off the seat post since it was all the way down...

Always the same profile too- a guy in spandex that shouldn't be allowed to buy it, let alone wear it! I still go around in bike shorts, but at least I was once a fast Cat4. (Ok, average CAT4...)

Sizng a lathe is no different... tasks dictate the 'best fit'. I can tell you descending down a fire road at Mount Snow where I raced my first Norba National, I wanted my saddle as low as possible to minimize "the damage". On a climb, I want it "in the normal position", unless I was climbing out of the saddle, because I got tired of being whacked in the "backside" by the saddle.

I know it's easy to raise the spindle height, but lowering it seems to be only addressed by raising the turner... Think about Geoffrey Noden's Adjust-a-Bench concept and it doesnt seem so out-there

S

Re: Lathe height questions

#10

Steven Antonucci

Only works to bring the center up...

steve antonucci

>unless I glue them to my shoes?

What if my spindle is too high and I want it lower. Sure I can build a platform, and move it, but it seems to me that's not practical unless I only turn one type of object.

adding and lowering 2X stock also introduces vibration since I raise the center of gravity. Just like a bicycle, I want to be on the SMALLEST possible lathe, with as much direct contact to the floor as possible.

I guess that's why people have multiple lathes...

steve

Re: Lathe height questions

#11

Nipple height

Jorge Castaneda ~ Downeast Maine

>Allen,

The elbow is way too low, I found that nipple height is good for me, don't bend at all.

Re: Lathe height questions

#12

Re: Lathe height questions

Steve in NC

>Allen

Congrats on the new toy. What did you settle on.

Re: Lathe height questions

#13

Ergonomics for Less Body Fatigue

Jake Niedling

>It is my understanding that the more you can keep your body in a nuetral position, then you will have less fatigue after long hours of working on the lathe. The general starting point is the spindle at elbow height. As all the other comments have mentioned that your nuetral postion may change with what you are turning and perhaps your body and tool position at the lathe. Try a change and see how you like it.

Re: Lathe height questions

#14

Dick Hines

Re: Nipple height

Dick Hines

>I am 6'5" and my lathe is at 52". I turn mostly bowls and hollow froms. I have a PM 3520 and can stand upright at the end of the lathe.

Re: Lathe height questions

#15

I can walk under Dick's lathe.....

Barry Irby

>standing up. I knew something was wrong when I realized I was buying my clothes at the "Extra short, Extra dumpy Store". My spindle is at 42". I'm raising it just because I have spindle envy. And a knotted muscle in my back.

Re: Lathe height questions

#16

Re: Lathe height questions

Allen Neighbors

>Thanks, Jim, appreciate your thoughts.

Allen

Re: Lathe height questions

#17

Re: It depends on what you turn

Allen Neighbors

>Steve, why do you say that lower is better for hollow forms?

Allen

Re: Lathe height questions

#18

Re: Thanks for the comments:

Allen Neighbors

>I think from what I've read so far, that it all depends on the person's likes or dislikes. I guess there's no real danger involved in a higher spindle. (Other than the center of gravity that was mentioned.)

Someone mentioned that I might be stooping to see... my optometrist made me a set of glasses that work well for turning, especially when I'm trying to peer inside a hollowform or vase. But I'm always stooping... either turning or looking.

Steve A. said he thought the lathe should be lower for hollowforms. Hollowforms is what I have my most trouble with... my back kills me when I bend over so much... that's why I've been thinking about 49". Dick, your height of 52" sounds even better, I may try that, later.

Jorge said nipple height was better for him, so he didn't have to bend over at all. I like that idea. There were other comments, but I can't remember all the names... thanks, though.

And Jim said go for it. I think I will.

I just wanted to make sure that when I raised it higher than the recommendation, that I wasn't going to have something that I hadn't thought of sneak up and bite me.

Thanks again, everybody.

Allen

Re: Lathe height questions

#19

Re: Oh, yes,

Allen Neighbors

>Steve in NC, I settled on the Oneway 1640, and it shipped this morning. :o)

Allen

Re: Lathe height questions

#20

Steven Antonucci

Like everything else, it depends...

steve antonucci

>When I was at Ellsworth's workshop, a lot of people were asking about the captured hollowing tools systems, and I don't use them. Much like Ellsworth, I turn through small openings and with hand held tools. I lose a lot of hollowforms too :-)

When I turned at Ellsworth's Poolewood, I was amazed at the better leverage and control I had by being able to keep my weight on top of the tool. The spindle height was easily 2-3" below what 'normal' wisdom says (elbow height). I'm 6'1", and initially I was tempted to ask one of the other guys to trade lathes with me, but David recommended I "try it". Within a day, I was a convert. Rather than having my arm away from my body, I could comfortable tuck the tool against my side.

I also found that a shear scraping cut on the outside of the form was easier because the tool was inline with my hips and my upper body was very still. As a result, I have started sanding the outsides with 150/220 vs. my normal 100G.

That's just my observations. YMMV.

steve

Re: Lathe height questions

#21

Exactly Steve - NM

georgetroy

>

Re: Lathe height questions

#22

with a little luck ...

Bob Fawcett

>It should make it to Texas by Friday. Are you getting lift truck to the house or terminal pickup?

If you pick it up at the terminal you can usually get it a day or 2 sooner. A couple of friends to help move it. You could load it in the back of the truck. Seems like I remember a top on the back of your truck - oh well.

Wish I could be there to help you set it up.

Re: Lathe height questions

#23

Re: with a little luck ...

Allen Neighbors

>Bob, I have a small (4x8) trailer connected to my riding lawnmower with a 2" ball. Due to the configuration of my shop entrance, and the layout of my back yard, it's the only way I could figure out to get it there. I'll be able to back the little trailer right up the ramp to the door.

I am also fortunate enough to be a volunteer firefighter, and several of the guys have said they will be ready at a moments notice to come help get it off the trailer and onto the leg pads I already have installed. This lathe will be located in the center of my shop. :o)

I invite to you to "come on down"... I'll let you help me set it up.

Allen

The electricity was installed today, and I am ready ready ready...