Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Troubles with Nova 3000

Posts

Troubles with Nova 3000

#1

Troubles with Nova 3000

Jorge Castaneda ~ Downeast Maine

>Hi there,

My lathe has several aflictions, the most frequent is the tool rest moving, then sometimes the tailstock too, from day one the head and tail are misalignedby 1/16", both vertically and horizontally and now the head has started to move too, if any of you has found a way to solve any of tese problems, I will be glad to hear how you did it.

Thank you very much

Jorge

ps I fail to mention that there is a vibration forever present, if I tough the tool rest with a tool, it sounds like a tunning fork... have not been able to figure out what causes it.

Re: Troubles with Nova 3000

#2

Re: Troubles with Nova 3000

John Lucas

>Jorge Check the cleanliness of the head where it swivels. It's very easy to get dirt under the headstock and it will change the alingment. Also check the pulley alingment and set screw tightness. They come loose often.

Re: Troubles with Nova 3000

#3

Re: Troubles with Nova 3000

Barry Irby

>I have a Nova 3000 DVR. I know the head stock is completely different, and mine does not vibrate noticeably. Glad I got something for the big bucks difference. A tuning fork noise would drive me nuts. When I first got it I was fanatical about keeping the ways clean and shiny, but I turn a lot of green wood, and I read about David Ellsworth saying to pile some wet shavings on the bed to season it a bit. So now I scrape of the crud and leave the rust. The tool rest and tail stock hold better. Not as well as I would like, but better. (Of course, I would like for them to stay put if I locked them down and then threw the lathe out of the space shuttle and checked it after reentry without a chute.)

One annoying problem is that the banjo "screams" when I move it. It was suggested I wax the ways. Hmmm, a choice between a scream and a banjo that won't stay put?

I do lubricate the cam in the banjo occasionally, but am careful not to get oil on the ways.

Nova should address this problem, but that won't help you or me.

Re: Troubles with Nova 3000

#4

Re: Troubles with Nova 3000

Bill Howatt

>Demo done at our club last night on a DVR. Everytime the presenter moved the banjo it gave out a sound as bad as fingernails on a blackboard. Didn't seem to compromise the quality of work though. :)

Bill

Re: Troubles with Nova 3000

#5

I had that problem with my Vicmarc 300

TDaniel

>Hi Jorge

I had a problem with the toolrest on my VL300. I discussed the problem with Victor at Orlando; or at least I tried to. The toolrest just would not stay where I put it; neither the banjo or the rest. A student broke the plastic handle off trying to get it to stop turning, then I replaced the handle with a box-end wrench and hex bolt so that I would have more leverage to get it tighter. This helped initially but after a short time the post was so dented by the hex bolt that I had to remove it and file off the marred areas. Finally I replaced the whole outfit with a One-way unit; problem solved! Sometimes you get so aggravated by one thing that doesn't work that you overlook all the good things about a lathe. To me the most important part of a lathe is the banjo and toolrest because it is what you move the most. You would think more manufacturers would appreciate this.

Re: Troubles with Nova 3000

#6

Re: Troubles with Nova 3000

Barbara Gill, Remlik VA

>Get in touch with the Nova technicians. If the lathe is still under warranty you can get a lot replaced and taken care of. They will also give detailed instructions about making sure the alignment pin is in the correct place. I used to have to align my headstock and tailstock frequently. In fact I bought one of those double Morse tapers to make the job easier. The screws you need to loosen to adjust the tailstock were overtightened so it was a challenge to get them free.

Re: Troubles with Nova 3000

#7

Re: Troubles with Nova 3000

Jorge Castaneda ~ Downeast Maine

>Hi John,

I guess it is time to dissasemble it again and blow air everywhere and reassemble, I know th eroutine...

Thank You!

Re: Troubles with Nova 3000

#8

Re: I had that problem with my Vicmarc 300

Jorge Castaneda ~ Downeast Maine

>Hi Terry,

I noticed your hybrid lathe, I agree, the banjo and tailstock are very important, I will look into a oneway banjo.

Thank you

Jorge

Re: Troubles with Nova 3000

#9

Re: Troubles with Nova 3000

Jorge Castaneda ~ Downeast Maine

>Hi Barbara,

I will get one of those double morse taper aligner, and will call the technicians, the tailsock is lower and out of aligment, and the moving head makes imposible to use the kelton coring system.

Thank you for the advice

Jorge

Re: Troubles with Nova 3000

#10

Re: Troubles with Nova 3000

Carole Valentine

>Barb, how DID you ever get them free? I tried and couldn't. I use the alignment tool as well, but I am wondering if I would still have to use it if I could get the tailstock bolts free to change the alignment.

Re: Troubles with Nova 3000

#11

Re: Troubles with Nova 3000

Bob Fawcett

>Hi Carole,

I don't own a Nova, but I spent many years as an auto mechanic. There is an impact driver sold that is great for losening tight screws. It takes a socket and can be used on bolts and screws with a screwdriver adapter. This is not the fancy tool you hook to an air compressor or is powered by 'lectricity. You hit it with a hammer. The hammer drives the screwdriver into the head at the same time it applys a lot of torque.

Here is a link that shows a picture.

http://www.mytoolstore.com/kd/kdspec02.html

These used to be a lot cheaper than this one. They may have gone up that much or maybe a further search would give a better price. Should be able to find one of these at an auto parts store or Sears.

Re: Troubles with Nova 3000

#12

Re: Troubles with Nova 3000

Jim Pugh, Ohio

>Barry, you might help the "screaming banjo" by removing it from the lathe, turning it over and using a small file, break every sharp edge your fingers can find. My 3000 and the DVR banjo had very sharp edges from when the bottom was milled flat so I did the file treatment and it helped quite a bit.

Re: Troubles with Nova 3000

#13

Thanks

Barry Irby

>I will try that. That thing can really scream.

Re: Troubles with Nova 3000

#14

Re: Troubles with Nova 3000

Barbara Gill, Remlik VA

>When I sent the headstock back I also sent the tailstock. They loosened the things. You would think that after awhile they would figure out that giving consumers a lathe with a tailstock that needs to be adjusted but can't be is unacceptable.

Re: Troubles with Nova 3000

#15

Re: Barry, you might also

Allen Neighbors

>try filling any empty spot beneath the banjo with J-B Weld... I'm talking of any place that wouldn't be in use in any of the positions you could put the banjo in... does that make sense? :o)

Filling those empty places would have a tendency to absorb some of that harmonic whine.

I think.

Allen

Re: Troubles with Nova 3000

#16

Keith Tompkins

Re: Troubles with Nova 3000

Keith Tompkins

>JIm, You beat me to it. That's what I do on my lathe(General)as well, then ease the edges with fine sandpaper.Also, My tailstock unit is adjustable, so I can adjust the tension. I don't know if the Nova is.

Re: Troubles with Nova 3000

#17

Ditto on the impact driver

Gary Evans Tallassee, TN

>Hey Carole,

Back in the old days, when I was a motorcycle mechanic and everything was put together with phillips head screws, the hammer-driven impact driver was indespenseable, particularly after the customer had been working on those screw heads for awhile.

Once you get one, you'll find plenty of uses for it. I'm still using the one that I bought 30 years ago.

Gary

Re: Troubles with Nova 3000

#18

alignment pin

John Lucas

>You don't need one of the alignment thingy's. I had one and it worked but aligned my head perfectly and then drilled a 3/16" hole at the joint between the headstock and bed. Then All I had to do when I needed to align the headstock was to rotate it until the butt end of the 3/16" drill fit ito this hole and lock it down. This was faster than the double ended morse taper.

Re: Troubles with Nova 3000

#19

Re: Troubles with Nova 3000

gtw

>You Guys and Gals don't know what trouble is with a Nova Lathe. If you sent me a e-mail I will explain further.

CAVEAT EMPTOR

Trevor

Re: Troubles with Nova 3000

#20

Warranty

W.C. Turner

>Under warranty or not, I wouldn't hesitate to contact the Mfg., and ask to speak to someone "In A Position Of Authority" and complain loudly, in order to get some satisfaction. There's no excuse for the troubles you report.