Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Box Turners............Feedback

Posts

Box Turners............Feedback

#1

Box Turners............Feedback

Greg H. from Wisconsin

>I have been turning bowls and now I'm looking to move on into boxes. I have a few questions for those who turn them.

What chuck is preferred, yes I know the smaller sizes, but vicmarc or oneway????

Best videos or books out there for "Boxes for Dummies," like me?

I'm fortunate enough to have two excellent box turners in our club. What is preferred for tools?? One uses the Sorby Multi Tip alot, the other a plethora of scrapers????

Thanks

Greg

Re: Box Turners............Feedback

#2

Re: Box Turners............Feedback

georgetroy

>I prefer the Vicmarc VM100 for small boxes. Compression grips from 1-3/8" to 2 1/4". Expansion from dovetail 1 3/4 - 2 3/4". Does not mark your work. Precision made, use a key for tightening. I also have Talon but it marks the work. Packard stocks the chuck. Tools for boxes gouges and scrapers,almost too numerous to list. GT

Re: Box Turners............Feedback

#3

Re: Box Turners............Feedback

Greg H. from Wisconsin

>Thanks for the advice.

Re: Box Turners............Feedback

#4

Re: Box Turners............Feedback

Jake Niedling

>Greg, I have the big oneway stronghold and it works great for boxes. I think any of them will work just fine. I always grip on the outside of a tenon. Yeah it leaves marks, but this all gets turned away when I reverse turn the bottom of the box. As far as tools: gouge, round nose scraper, flat scraper sharpen on both the end and the left side.

Re: Box Turners............Feedback

#5

Re: Box Turners............Feedback

Kevin Gerstenecker

>As far as instructional material for learing to turn boxes, either the book or video, "Turning Boxes" by Richard Raffan is about as good as it gets, IMO. I have both, and they show in detail the "How to's" of box turning. I do a couple of little things differently than Raffan, but by and large, the process is the same, and works well.

Re: Box Turners............Feedback

#6

Re: Box Turners............Feedback

Russell L. Babbitt Jr.

>Tools? Spindle gouge, scrapers, one scraper I use I gound myself, but is sold as a box scraper, checkout Craft Supply.

Videos? Bonnie Klein, Chris Stott

Books? Chris Stott - Turned Boxes 50 Designs. A great book with how-to and sample designs.

Re: Box Turners............Feedback

#7

Re: Box Turners............Feedback

Fog Tanner

>I turn a lot of boxes, got my start from the Raffin Turning Wood and Turning Boxes video and books. I have also seen the Ray Key and Chris Stott videos, both worth watching, but I still use the Raffin method for fitting the lid. Its worth watching all three and then make some boxes and watch them again to find out what you did wrong.

I use a 1/2" gouge for back hollowing the inside and a couple of scrapers for finishing the inside. They are round nose with the left side ground down the side. for Square bottom I use several different square end plus a negative rake for the vaery bottom. for the outside, I mainly use a skew (1/2", 3/4" and 3/8") depending on the shape I may also have to use a gouge (1/4" or 3/8"). For finishing the Bottom I use a 3/8" gouge ground at a 30 degree angle and a 1/2" negative rake scraper.

If you are making suction fit lids, this takes the most practice and can only be had by making a lot of boxes.

Re: Box Turners............Feedback

#8

Re: Box Turners............Feedback

Bob Fawcett

>Craft Supply now has smooth jaws for the Oneway chucks so you can have non-marking grip from them also.

Re: Box Turners............Feedback

#9

Chucks For Boxes? Take Your Pick.

Barry Turner

>It doesn't take a terribly good chuck to hold stock for boxes. The stock is usually smaller, not subject to the forces of bowl turning and doesn't require a death grip from the chuck. I have been very successful using a Nova Compac chuck and later, a Super Nova. I wouldn't hesitate to buy another.

Re: Box Turners............Feedback

#10

Re: Chucks For Boxes? Take Your Pick.

eliot

>Tools? It may seem like cheating, but a really easy, safe way to turn the inside of a box is with a Dennis Stewart type tool that's held in an arm brace. I usually use it with a square-ended bit so that I can get into the deep corner. It's probably overkill for small boxes, but it works great for deeper boxes.

Re: Box Turners............Feedback

#11

Re: Box Turners............Feedback

Ron McKinley

>Greg, I'm still somewhat of a novice but I've turned several dozen boxes using the Apprentice chuck (from Craft Supples) with all the different jaws. It's the same as the Barracuda 2 from Penn State.

I use a heavy duty 3/8" thick, 3/4" wide round nose scraper (Henry Taylor) and a Sorby flat scraper plus a small 1/4" wide/thick tool I made myself. It's ground flat across the end and tapers down the side on the left side.

I watched the Raffan videos and while he's fun to watch, he goes too fast to really follow when you're learning. Christ Stott videos are very helpful and I just got the three-video set of Ray Key making 3 different type boxes. With all that I should be an expert�well, maybe in a few years. I use the Raffan method of fitting the lid and I get it right most of the time........Ron