Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Questions about pen turning

Posts

Questions about pen turning

#1

Questions about pen turning

Josh in VA

>Guys, I am relatively new to pen turning compared to probably all of you. I have turned about 50 or so pens, and still have a lot to learn. My pens have been getting better due to better finishing and more patience while turning.

I have two questionshopefully you can help me with:

I have an El Presidente pen kit I am wanting to turn, what have you guys done to end mill these kits. I have been looking for sleeves to use, but am not having any luck. Any ideas on where I can get some sleeves or any other tricks?

While turning a pen, do any of you use a skew chisel? I have used it occasionally, but am not convinced on why I should be using it at all.

Thanks

Josh

remove no spam for email

Re: Questions about pen turning

#2

Good questions, questionable answers

Bert

>I turn some larger pens and have the same problem. For the past several I've cheated and used my parting tool to trim the very ends of the pen parts down to the brass tube. Then I glue on a predrilled piece of contrasting wood cut from either 1/8 or 1/16 stock.

what I end up with is a maple pen with the ends framed in Purple Heart or ebony. I kind of like the look and will try to post a pic or two if I can find the time. This eliminates the need to mill the ends before turning because I can "mill" it on the lathe. The end pieces are from flat stock so they make clean ends automatically.

As for the skew, some times I love it and sometimes I don't. I have forced myself to turn entire projects with it as a learning experience and as a result I can use it with a fair amount of confidence. But like you, sometimes I wonder how much I would miss it if I didn't have one. Beads would be more dificult but for pens?

Good luck.

Re: Questions about pen turning

#3

Re: Questions about pen turning

eaglesc

>You will not finf all the different shafts for all the different tubes because of the varied sizes of tubes.

I glue up a maple blank on a slim line or 8mm tube and turn my own.

The 4 piece mill set from Worrdturningz(psi) has 7mm,8mm, 3/8ths and 10 mm shafts.

You can also buy extra cutters.

I had a mill from WC for a while but the head was too small and the screw end finally broke off.

I turn mostly with a round nose scraper and a skew, can't get a "finished" look with a gouge, less sanding with a skew.

Re: Questions about pen turning

#4

Re: Questions about pen turning

Terry Quiram, Roanoke Illinois

>Josh

I turned a sleeve for the Cigar pens. I made it from Corian. The process is a little fumble fingered but it is cheaper that one of those "all size end mill" kits. As far as using a skew, depends if I hate it or love it for that particular day.

Terry

Re: Questions about pen turning

#5

Steven Antonucci

Funny you should ask...

steve antonucci

>I turned a pen a few minutes ago... probably my 100th, and I'm still learning too.

I do use a skew, but only on my last pass. Spindle gouge for roughing out. I happen to have a lot of pen bushing, and some of them are perfect for cigar pens and my 7mm end mill. I want to say that they are for mini european kits, but I can't be 100% certain. If you own a lathe :-), couldn't you mill a sleeve and other bushings on your own? Aluminum or brass should be soft enough.

Steve

Re: Questions about pen turning

#6

Re: Questions about pen turning

Josh in VA

>Thanks for the input guys. I do have quite a bit of extra corian around so I will mill my own sleeves.

As far as the Skew, I guess I will just keep playing with it and improving my technique.

Thanks

Josh

Re: Questions about pen turning

#7

What I Do

Jim Shaver Oakville, Ont.-Let's Go Oilers!

>Hi Josh,

I have not turned the El Presidente kit. I turn a lot of pens in a year (350-400 pens/yr), a wide variety of kits as well. When it comes to pen mill�s I have several. I use the PSI multi set, it covers a wide range of popular sizes. I also have a healthy selection of mills from Craft Supply. Craft Supply make interchangeable guides that are made to fit a specific tube diameter, often unique to Craft Supply kits. If I get a tube size that I can not fit just right I will mill a sleeve to fit my 7mm mill. I do know some pen turners who do not use an end mill, but I am not clear on their process.

I used to turn my pens with a spindle gouge until about 2-3 years ago when I finally went back to the skew. It all started with the Alan Lacer video on the Skew. I watched it a few times and went out and practiced with it. It took me awhile but once I got it down I knew I would never go back to a spindle gouge again. I now have 5 skews and I love the clean surface the skew leaves�.sometimes it�s almost a shame to sand it. I have found the secret for me with the skew is to grind the edge then hone often with a diamond plate, some times three or four times on a stabilized or acrylic blank. I always hone the edge before making �the Money Cut!�

Like others have mentioned it all takes practice and time with the tools and working your process.

Take care,

Jim

Re: Questions about pen turning

#8

Re: Questions about pen turning

Ron in Drums PA

>Here is what I do


I've use hardwood, discarded pen blanks and corain, they all work well

Re: Questions about pen turning

#9

Re: Questions about pen turning

Bill Hale

>Josh

Try this link

www.penturners.org

good turning and be safe

Bill in Dolores,CO.